York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 129 / 160

JOHNSON CONTROLS

129

SECTION 2 – OPTIVIEW CONTROL CENTER

FORM 160.79-O3

ISSUE DATE: 11/09/2018

While the Vanes are closing during a soft shutdown, if

a Local stop or any faults listed above occur, the soft

shutdown is terminated and the chiller immediately

enters “Coastdown”.

Run Messages

“LEAVING CHILLED LIQUID CONTROL”

The chiller is running, controlling the Leaving Chilled

Liquid to the Leaving Chilled Liquid Temperature Set-

point. There are no system conditions inhibiting this

operation.

"SYSTEM IN LEAD COMPRESSOR PULL-

DOWN"

Displayed while a LEAD COMPRESSOR PULL-

DOWN TIME Setpoint (0-255 minutes) is in effect.

The time remaining in the period is also displayed. For

the duration of this period, only the Lead compressor

will be permitted to run. The Lag compressor will not be

brought on line during this period. A current limit may

be applied to the Lead motor during this period using

the LEAD COMPRESSOR PULLDOWN DEMAND

LIMIT setpoint (30-100%). See the complete expla-

nation in

SECTION 1 – DESCRIPTION OF SYSTEM

AND FUNDAMENTALS OF OPERATION

“LEAD MOTOR-HIGH CURRENT LIMIT”

Either the Lead Compressor Pulldown Demand Time

Setpoint is in effect and the lead compressor motor

current is being limited by the Lead Compressor Pull-

down Demand Limit Setpoint, or the Lead Compres-

sor Pulldown Demand Time Setpoint has elapsed and

the lead compressor motor current is being limited by

the Chiller Current Limit Setpoint.
Refer to the MOTOR screen for details of the condi-

tions above.
When the motor current increases to the “inhibit open”

threshold, the Pre-rotation Vanes are inhibited from

further opening. This prevents a further current rise. If

the current continues to rise to the “start close” thresh-

old, the Vanes begin closing until the current falls to

the “stop close” threshold. Automatic Vane opera-

tion is resumed and this message automatically clears

when the motor current decreases to the “allow open”

threshold.

“LAG COMPRESSOR PRELUBE”

A start has been initiated on the lag compressor and

the 50 second pre-start lubrication is being performed.

“LAG COMPRESSOR COASTDOWN”

The lag compressor has shutdown and the 150 sec-

ond post-run lubrication is being Performed on the lag

compressor.

“LAG COMPRESSOR UNLOADING BEFORE

SHUTDOWN”

Displayed while the Pre-rotation Vanes and Discharge

Valves are closing during a soft shutdown of the lag

compressor.

“VANES #1 START INHIBIT-MOTOR SWITCH

OPEN”

Compressor #1 is inhibited from starting because its

Pre-rotation Vanes are not fully closed (Vane Motor

Switch open), but compressor #2 is able to run and

thus the chiller is not prevented from operating. This

message clears when the Vanes have fully closed.

“VANES #2 START INHIBIT-MOTOR SWITCH

OPEN”

Compressor #2 is inhibited from starting because its

Pre-rotation Vanes are not fully closed (Vane Motor

Switch open), but compressor #1 is able to run and

thus the chiller is not prevented from operating. This

message clears when the Vanes have fully closed.

“MOTOR #1 START INHIBIT – ANTI-RECY-

CLE”

Compressor #1 is inhibited from starting because its

30 minute anti-recycle period is in Effect, but com-

pressor #2 is able to run. This message clears when the

30 minute timer expires.

“MOTOR #2 START INHIBIT – ANTI-RECY-

CLE”

Compressor #2 is inhibited from starting because its

30 minute anti-recycle period is in Effect, but com-

pressor #1 is able to run. This message clears when the

30 minute timer expires.

START INHIBIT MESSAGES

“DISCHARGE VALVE #1 - OPEN”

The chiller (both compressors) is inhibited from start-

ing because compressor #1 Discharge Valve is not

closed. This start inhibit is released when the valve has

fully closed.

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды