York 160.87-OM1 Скачать руководство пользователя

Страница: 208 / 268

VSD – Harmonic Filter-DC Bus Voltage Imbalance

If the Half DC Link Voltage does not remain within plus or minus 63VDC of the DC Link Voltage

divided by 2, this shutdown is performed.

Harmonic Filter – Input Current Overload

The three phases of RMS Filter current are monitored. If any one of the three phases continuously

exceeds a given threshold for 7 seconds, a chiller shutdown is performed and this message is

displayed. The maximum permissible continuous RMS current ratings for the Harmonic Filter are:

•

351/292 HP equals 128 Amps

•

503/419 HP equals 176 Amps

•

790/658 HP equals 277 Amps

•

1048/917 HP equals 385 Amps

Harmonic Filter – Logic Board Power Supply

The low voltage power supplies on the Filter Logic Board have decreased below their permissible

operating range. The Filter Logic Board receives its power from the VSD Logic Board via the ribbon

cable, connecting the two boards.

Harmonic Filter – Run Signal

When a digital run command is received at the Filter Logic Board from the VSD Logic Board via

the 16 position ribbon cable, a 1/10 second timer is started. If a redundant run command does

not occur on the serial data link from the VSD Logic Board before the timer expires, a shutdown is

performed and this message is generated.

Harmonic Filter – DC Current Transformer 1

During initialization, with no current flowing through the DC Current Transformers (DCCT’s), the

DCCT output voltages are measured and compared with a preset limit via the Filter Logic Board. If

the measured values exceed the preset limits, the DCCT’s are presumed to be defective and this

shutdown is generated.

Harmonic Filter – DC Current Transformer 2

See

Harmonic Filter – DC Current Transformer 1

message above.

Safety shutdown messages

Evaporator – Low Pressure

The Evaporator Pressure, as sensed by the Evaporator transducer, has decreased to the safety

shutdown threshold. For water cooling applications, the safety shutdown threshold is a fixed value

for the respective refrigerant. For Brine cooling applications, the safety shutdown threshold varies

according to the concentration of the Brine solution. The Brine shutdown threshold is programmed

at the YORK Factory. It should not be changed by anyone other than a qualified Service Technician

following instructions in

OptiView Control Center – Service Instructions (Form 160.54-M1)

. The chiller

can be started after the Evaporator Pressure increases to the restart threshold and the Compressor

Switch is placed in the Stop-Reset (O) position.

YK-EP Style B Centrifugal Chiller

208

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды