York 160.87-OM1 Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 268

York 160.87-OM1 Скачать руководство пользователя страница 130

Motor details screen

Figure 47: Motor details screen

This screen displays information pertinent to the Motor Monitoring feature. The feature consists

of motor winding temperature, motor bearing temperature, motor bearing vibration and motor

cooling coil leak detection. Setpoints on this screen allow any combination of these items to be

enabled or disabled based on the equipment applied. The motor could be equipped with different

types of sensors for this monitoring. Either RTD's or Transmitters could be applied for winding and

bearing temperature monitoring. Motor cooling coil leak detection could be done with either an

optical or float sensor. Setpoints on this screen allow for the enabling of the actual sensor type

applied.
Vibration baseline data can be entered manually or by running an auto baseline routine that plots a

baseline over a 1 hour period while the chiller is running.
This screen also serves as a gateway to a subscreen that allows programming of the winding

High Temperature Warning/Safety Shutdown thresholds and bearing High Temperature and High

Vibration Warning/Safety Shutdowns. Also, individual winding temperature sensors can be disabled

on this screen.

Table 130: Display only

Field/LED name

Description

Motor Run (LED)

Illuminates when the OptiView Control Center is commanding the

motor to run.

%Full Load Amps

Displays the motor current as a percentage of chiller Full Load

Amps.

Output Frequency

Only displayed when Motor Drive Type Setpoint is set to any VSD.

Displays the frequency at which the VSD is operating the motor. This

value is returned from the VSD Logic Board.

YK-EP Style B Centrifugal Chiller

130

«
...
128
129
130
131
132
...
»

Содержание 160.87-OM1













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды