York International ZQ Series Скачать руководство пользователя страница 18

Страница: 18 / 92

Figure 17: Condensate Drain

Compressors

The compressor used in this product is specifically

designed to operate with R-410A Refrigerant and

cannot be interchanged.

CAUTION

This system uses R-410A Refrigerant which operates

at higher pressures than R-22. No other refrigerant

may be used in this system.

The compressor also uses a refrigerant oil that is

extremely hygroscopic, meaning it absorbs water

readily. They can absorb 15 times as much water as

other oils designed for HCFC and CFC refrigerants.

Take all necessary precautions to avoid exposure of

the oil to the atmosphere.

CAUTION

Do not leave the system open to the atmosphere. Unit

damage could occur due to moisture being absorbed

by the

refrigerant

in the system. This type of oil is

highly susceptible to moisture absorption.

R-410A compressor lubricants are known to cause

long term damage to some synthetic roofing

materials.

CAUTION

Exposure, even if immediately cleaned up, may cause

embrittlement (leading to cracking) to occur in one

year or more. When performing any service that

may risk exposure of compressor oil to the roof, take

precautions to protect roofing.

Procedures which risk oil leakage include, but are

not limited to, compressor replacement, repairing

refrigerant leaks, replacing refrigerant components

such as filter drier, pressure switch, metering device

or coil.
Units are shipped with compressor mountings

which are factory-adjusted and ready for operation.

CAUTION

Do not loosen compressor mounting bolts.

Filters

Two-inch filters are supplied with each unit. Four-

inch filters may be used with no modification to the

filter racks. Filters must always be installed ahead of

evaporator coil and must be kept clean or replaced

with same size and type. Dirty filters reduce the

capacity of the unit and result in frosted coils or

safety shutdown. Refer to physical data tables, for

the number and size of filters needed for the unit.

The unit should not be operated without filters

properly installed.

Power And Control Wiring

Field wiring to the unit, fuses, and disconnects must

conform to provisions of National Electrical Code

(NEC), ANSI/NFPA No. 70 – Latest Edition (in U.S.A.),

current Canadian Electrical Code C221, and/or local

ordinances. The unit must be electrically grounded

in accordance with NEC and CEC as specified above

and/or local codes.
Voltage tolerances which must be maintained at the

compressor terminals during starting and running

conditions are indicated on the unit Rating Plate and

Table 1.

INSTALLATION MANUAL ZQ SERIES 3 - 5 ton 60 Hertz R-410A

Johnson Controls Ducted Systems

Содержание ZQ Series




























































































Результаты поиска

Содержание ZQ Series

Отзывы:

Бренды по названию

Популярные бренды

York International ZQ Series, Руководство по установке

Результаты поиска

Содержание ZQ Series

Отзывы:

Бренды по названию

Популярные бренды