YOKOGAWA wt3000 Скачать руководство пользователя страница 9

Страница: 9 / 384

IM 760301-01E

Safety Precautions

This instrument is an IEC safety class 01 instrument (provided with a terminal for

protective earth grounding).

The general safety precautions described herein must be observed during all phases of

operation. If the instrument is used in a manner not specified in this manual, the

protection provided by the instrument may be impaired. Yokogawa Electric Corporation

assumes no liability for the customer’s failure to comply with these requirements.

The following symbols are used on this instrument.

“Handle with care.” (To avoid injury, death of personnel or damage to the

instrument, the operator must refer to the explanation in the User’s Manual or

Service Manual.)

Electric shock, danger

Alternating current

Both direct and alternating current

ON (power)

OFF (power)

ON (power) state

OFF (power) state

Grounding

Failure to comply with the precautions below could lead to injury or death or damage

to the instrument.

WARNING

• Use the Instrument Only for Its Intended Purpose

The WT3000 is a power measurement instrument that can measure parameters

such as voltage, current, and power. Do not use this instrument for anything

other than as a power measurement instrument.

• Check the Physical Appearance

Do not use the instrument if there is a problem with its physical appearance.

• Use the Correct Power Supply

Before connecting the power cord, ensure that the source voltage matches the

rated supply voltage of the instrument and that it is within the maximum rated

voltage of the provided power cord.

• Use the Correct Power Cord and Plug

To prevent the possibility of electric shock or fire, be sure to use the power cord

supplied by YOKOGAWA. The main power plug must be plugged into an outlet

with a protective earth terminal. Do not disable this protection by using an

extension cord without protective earth grounding.

Содержание wt3000

































































































































































































































































































































































































Результаты поиска

Содержание wt3000

Отзывы:

YOKOGAWA wt3000, Руководство пользователя, Страница: 9 / 384

Результаты поиска

Содержание wt3000

Отзывы: