YOKOGAWA WT1800E Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 154

YOKOGAWA WT1800E Скачать руководство пользователя страница 95

16-1

IM WT18O1E-02EN

16.1 Configuring Storage Control

This section explains the following settings for storage control:
•  Storage mode
•  Storage count
•  Confirming and optimizing the maximum storage count
•  Storage interval
•  Scheduled times for real-time storage
•  Trigger event (synchronization to a user-defined event)
•  Storage of numeric data when storage starts

►

“Storage Control (Control Settings)” in the features guide

Control Settings Menu

Press

SHIFT+STORE START

(STORE SET) and then the

Control Settings

soft key to display one of

the menus shown below. The menu that appears varies depending on the storage mode setting that
you have specified.

Manual Storage Mode

Set Store Mode to Manual.

Set the storage count (Infinite, 1 to 9999999).
Confirms and optimizes the maximum storage count

Set the storage interval.

Select whether to store numeric data when storage starts.

This soft key is displayed when Interval is set to a value other than 00 : 00 : 00.

Confirming and Optimizing the Maximum Storage Count

Press the

Optimize Count

soft key to display the following screen.

Maximum storage count (0 to the maximum number of times that data can be stored to the save

destination)

*

* The maximum number of times that storage can be performed depends on the number of stored items that

you have set and the free space at the save destination.

For details on how to set the stored items, see section 16.2. For details on how to set the save destination,

see section 16.3.

Even if you have specified a USB memory device as the save destination, if you remove the USB memory

device, the save destination switches automatically to the internal RAM disk. If you close this screen and

then open it again by pressing the Optimize Count soft key, the maximum storage count changes to the

value determined by the internal RAM disk,s free space.

Sets the storage count

The storage count is set to the maximum storage count

displayed to the left.

Setting the Storage Interval

Press the

Interval

soft key to display the following screen.

Set the storage interval

(00 hours : 00 minutes : 00 seconds to 99 hours : 59 minutes : 59 seconds).

Chapter 16 Storing Data

«
...
93
94
95
96
97
...
»

Содержание WT1800E



























































































































































Отзывы:

Нет отзывов