YOKOGAWA WT1800E Скачать руководство пользователя страница 129

Страница: 129 / 154

20-4

IM WT18O1E-02EN

20.3 Accessing this instrument from a PC (FTP

Server)

This section explains the following settings for accessing this instrument from a PC on a network:
• User name
• Password
• Timeout
• FTP client software

►

“FTP Server (FTP Server)” in the features guide

Configuring FTP Server Settings (FTP/Web Server)

Press

UTILITY

, the

Network

soft key, and then the

FT/WebP Server

soft key to display the following

menu.

Set the user name (up to 32 characters).

Set the password (up to 32 characters).

Set the timeout value (30 to 3600 s).

Applies the settings

FTP Client Software

Start an FTP client on a PC.
Enter the user name and password that you entered on the screen shown above to connect to this
instrument.

Note

If you set the user name to “anonymous,” you can access this instrument without entering a password.

Содержание WT1800E



























































































































































Результаты поиска

Содержание WT1800E

Отзывы:

YOKOGAWA WT1800E, Руководство пользователя, Страница: 129 / 154

Результаты поиска

Содержание WT1800E

Отзывы: