YOKOGAWA WE7281 Скачать руководство пользователя страница 50

Страница: 50 / 52

5-6

IM 707281-01E

Weight

Approx. 0.9 kg

Number of Used Slots

Standard Accessories

WE7281: Terminal block (1) (attached to the output connector at the time of shipment)

User’s Manual (1)

WE7282: User’s Manual (1)

Optional Accessories

WE7281: Terminal block (Model: A1460JT)

WE7282: None

Overvoltage Categories define transient overvoltage levels, including impulse

withstand voltage levels.

Overvoltage Category I: Applies to equipment supplied with electricity from a circuit

containing an overvoltage control device.

Overvoltage Category II: Applies to equipment supplied with electricity from fixed

installations like a distribution board.

Pollution Degree:

Applies to the degree of adhesion of a solid, liquid, or gas

which deteriorates withstand voltage or surface resistivity.

Pollution Degree 1:

Applies to closed atmospheres (with no, or only dry, non-

conductive pollution).

Pollution Degree 2:

Applies to normal indoor atmospheres (with only non-

conductive pollution).

Typical value represents a typical or average value. It is not strictly guaranteed.

5.3 General Specifications

Содержание WE7281





















































Результаты поиска

Содержание WE7281

Отзывы:

YOKOGAWA WE7281, Руководство пользователя, Страница: 50 / 52

Результаты поиска

Содержание WE7281

Отзывы: