YOKOGAWA WE7281 Скачать руководство пользователя страница 49

Страница: 49 / 52

5-5

IM 707281-01E

Specifications

5.3

General Specifications

Safety Standards

Complies with CSA C22.2 No.1010.1 and EN61010-1, conforms to JIS C1010-1

• Overvoltage Category CAT I and II

• Pollution Degree 1 and 2

EMC Standards

Emission

Complying Standard

EN55011 Group 1 Class A

This product is a Class A (for industrial environment) product. Operation of this product

in a residential area may cause radio interference in which case the user is required to

correct the interference.

Immunity

Complying Standard

EN50082-2

Testing Condition

• WE7281: Connect with the 3 m twisted pair wire.

• WE7282: Connect with the 3 m coaxial cable (3D-2W).

Standard Operating Conditions

Ambient temperature: 23

C, Ambient humidity: 50

10%RH, Error on supply voltage/

frequency: within 1% of rating, after the warm-up time has passed

Warm-up Time

At least 30 minutes

Maximum Common-Mode Voltage (between L Terminal and Ground)

WE7281:

250 VDC or

250 VACrms

WE7282:

42.4 VDC + ACpeak

Maximum Voltage between Channels

WE7281:

250 VDC or

250 VACrms

WE7282:

42.4 VDC + ACpeak

Withstand Voltage

Between output terminal and ground

WE7281/WE7282: 1500 VACrms at 60 Hz for one minute

Between channels

WE7281: 2300 VACrms at 60 Hz for one minute

WE7282: 1500 VACrms at 60 Hz for one minute

Insulation Resistance (between Output Terminal and Ground and between Channels)

10 M

Ω

or more at 500 VDC

Output Connector

WE7281: Clamp type terminal (terminal block is detachable)

WE7282: Isolated BNC

Maximum Output Cable Length

20 m (However, the output waveform may distort if the cable length exceeds 3 m.)

Operating Conditions

Same as those of the measuring station

Storage Conditions

Temperature: –20

C to 60

Humidity: 20% to 80%RH (no condensation)

Power Consumption

15 VA (typical value*

at 100 V/50 Hz)

External Dimensions

Approx. 33(W)

243(H)

232(D) mm (projections excluded)

Содержание WE7281





















































Результаты поиска

Содержание WE7281

Отзывы:

YOKOGAWA WE7281, Руководство пользователя, Страница: 49 / 52

Результаты поиска

Содержание WE7281

Отзывы: