YOKOGAWA WE7281 Скачать руководство пользователя страница 45

Страница: 45 / 52

5-1

IM 707281-01E

Specifications

Chapter 5 Specifications

5.1

Performance Specifications

The following performance specifications are attained under standard operating

conditions (section 5.3 “General Specifications”).

Common

Number of output channels

4 channels

Output format

Floating unbalanced output, isolated between channels

D/A resolution

16 bits (includes the sign)

Output range

1 V,

2 V,

5 V,

10 V

Maximum output current

10 mA (per channel)

Allowable load resistance

1 k

Ω

or more

Output impedance

Ω

or less

During DC Output

DC accuracy

(at ambient temperature of 23

C, ambient humidity of 50

10%RH, after the warm-up

time has passed)

Range Resolution DC Accuracy

Temperature Coefficient (5-18

C, 28- 40

1 V

0.1 mV

(0.05% of 0.5 mV)

(50 ppm of 33

V)/

2 V

1 mV

(0.05% of 1 mV)

(50 ppm of 54

V)/

5 V

1 mV

(0.05% of 2 mV)

(50 ppm of 116

V)/

10 V 1 mV

(0.05% of 4 mV)

(50 ppm of 220

V)/

Settling time

s (until the value settles within

0.1% of the final value, typical vlaue*)

Trigger source

Manual, bus trigger signal (BUSTRG1/BUSTRG2) of the measuring station.

During Function Waveform (FG) Output

Output waveform

Sine, pulse (variable duty cycle), ramp, triangular, arbitrary, and DC.

Output frequency range and resolution

1 mHz to 20 kHz (Sine wave), 1 mHz to 10 kHz (other waves)

Resolution: 1 mHz

Output frequency accuracy

(0.01% of s 23

Hz)

maximum output voltage

Range withing the output range

Amplitude range and accuracy

(at ambient temperature of 23

C, ambient humidity of 50

10%RH, after the warm-up

time has passed.)

Range Setting

Selectable range

Resolution

Accuracy (for 1-kHz sine wave)

1 V

0 to 2 Vp-p

0.1 mVp-p

4 mVp-p

2 V

0 to 4 Vp-p

1 mVp-p

8 mVp-p

5 V

0 to 10 Vp-p

1 mVp-p

20 mVp-p

10 V

0 to 20 Vp-p

1 mVp-p

40 mVp-p

Offset voltage range

and accuracy

Range Setting

Selectable Range

Resolution

Accuracy

1 V

–1 to 1 V

0.1 mV

2 mV

2 V

–2 to 2 V

1 mV

4 mV

5 V

–5 to 5 V

1 mV

10 mV

10 V

–10 to 10 V

1 mV

20 mV

Содержание WE7281





















































Результаты поиска

Содержание WE7281

Отзывы:

YOKOGAWA WE7281, Руководство пользователя, Страница: 45 / 52

Результаты поиска

Содержание WE7281

Отзывы: