YOKOGAWA VY Series Скачать руководство пользователя страница 9

Страница: 9 / 50

2. HANDLING PRECAUTIONS

This section describes the precautions to follow

when handling the product. Be sure to read this

section before using the product.

For information other than that described in this

section, refer to the related section.

If you have any problems or questions, contact

your nearest YOKOGAWA service center or sales

representative.

2.1 Checking Model and

Specifications

This instrument is inspected thoroughly before it is

shipped from the factory. When this instrument is

delivered to the installation site, check its external

appearance for damage, and make sure that all

parts for installation are provided.

Be sure that you have your model number (MODEL) and

serial number (No.) available when contacting Yokogawa.

The model code and specifications given on the

nameplate are those current when this product was

shipped from the factory.

F0201.ai

Figure 2.1(a) Example of Nameplate (Integral Type)

Remote Sensor

F0202.ai

Remote Transmitter

F0205.ai

Figure 2.1(b) Example of Nameplate (Remote Type)

2.2 Transportation and Storage

Precautions

To prevent damage to the vortex flowmeter due to

accidents during transportation, it should be carried

in its original packing condition.

Deterioration of insulation, corrosion or other

abnormalities may occur due to unexpected

situations if the vortex flowmeter is stored for a long

period of time after it is delivered to the user site.

When it is anticipated that the vortex flowmeter

will be stored for a long time, pay attention to the

following points.

(1) The vortex flowmeter should be stored in its original

packing condition in the storage location.

(2) Select a storage location that fulfills the following

conditions:
• A place where it will not be exposed to rain or

water

• A place subject to minimal vibrations or shocks

• Temperature and humidity levels should be as

follows: The preferred ambient temperature and

humidity levels are +25°C and approximately 65%
RH.

Ambient temperature: -40 to +85°C
Humidity: 0 to 100% RH (no condensation)

(3) When storing a vortex flowmeter after use,

completely clean the flowmeter to ensure that there
is no measured fluid remaining in its piping line and

on the shedder bar.

(4) If the vortex flowmeter is carried to the installation

site and is stored without being installed, rain
water might get inside and impair the instrument's
performance. Install, wire and perform other
installation work immediately after transporting the
vortex flowmeter to the installation site.

<2. Handling Precautions>

IM 01F07A01-01EN

Содержание VY Series



















































Результаты поиска

Содержание VY Series

Отзывы:

YOKOGAWA VY Series, Руководство пользователя, Страница: 9 / 50

Результаты поиска

Содержание VY Series

Отзывы: