YOKOGAWA vigilantplant DM8 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 63

background image

<4. OPERATION>

4-9

IM 12T03A01-02E

4.3.6

Pressure Compensation

Pressure compensation means to compensate the shift generated by measurement under

operating pressure. The compensation should be carried out as necessary only for calibration

under atmospheric pressure.
Measured value is affected up to +0.00005 g/cm

3

by 100 kPa pressure variance.

Therefore, for liquid under pressure approximating to the atmospheric pressure calibrated

value under atmospheric pressure can be used. Pressure compensation is to be carried out to

minimize effects generated by high operating pressure.

Compensation data is obtained by conducting sample liquid. Measure the data according to the

following procedure when the liquid density is stable. The procedure assumes that sample liquid

is already conducted according to Section 4.3.3.

(1) Fully open the needle valve “NV4” and read P from the pressure gauge. At the same time,

obtain density at the reference temperature indicated on the density converter.

(2) Fully close the ball valve “BV1”, and open the needle valve “NV3” to equalize the sample

liquid pressure in the detector to the atmospheric pressure. Obtain density at the reference

temperature indicated on the density converter.

(3) Calculate the compensation data using the densities obtained in (1) and (2).

Compensation data (g/cm

3

) =

Density under working pressure – density under atmospheric pressure

When calibration the compensation data should be subtracted from the density value of the

standard solution.

STEAM IN

CONDENSATE OUT

V2

a

a

V1

b

ST1

a'

a'

b'

TI

F

FM

NV1

PI

NV2

DD

NV3

NV4

BV1

Element specifications

F:

Strainer body; 316 SS

Element; 316 SS, or Ni (option)

PI:  Pressure gauge, 0 to 1MPa or 0 to 2MPa, 316 SS
TI:  Thermometer. 0 to 100 °C or 0 to 150 °C, 316 SS
FM:  Flowmeter, tapered metal tube flowmeter, 1 to 10 L/min, 316 SS
BV1:   Ball valve, 316 SS
NV1 to 4: Needle valve, 316 SS
DD:    Density detector
V1, V2: Valve
ST1:   Steam trap

SAMPLE IN

SAMPLE OUT

Figure 4.5

Flow Diagram

5th Edition : Dec. 11, 2015-00

«
...
48
49
50
51
52
...
»

Содержание vigilantplant DM8
































































Отзывы:

Нет отзывов

Похожие инструкции для vigilantplant DM8

Бренд: Callaway Страницы: 13

Бренд: Hach Страницы: 145

Бренд: Hach Страницы: 358

Polymetron 9582sc

Бренд: Hach Страницы: 280

Бренд: HACH LANGE Страницы: 15

Бренд: Polimaster Страницы: 6

Бренд: STONEX Страницы: 99

Бренд: PCE Health and Fitness Страницы: 11

Бренд: Camlab Страницы: 28

Бренд: LI-COR Страницы: 92

Бренд: R&S Страницы: 43

D-Mon Class 1000

Бренд: E-Mon Страницы: 26

Бренд: Cal Test Electronics Страницы: 14

Бренд: GREISINGER Страницы: 4

Бренд: McIntosh Страницы: 17

Бренд: Metrohm Страницы: 163

Liquicap M FTI51

Бренд: Endress+Hauser Страницы: 96

VG-STRANDBERG V-BDN

Бренд: Boss Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды