YOKOGAWA TB830D Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 85

YOKOGAWA TB830D Скачать руководство пользователя страница 78

<APPENDIX>

App.-1

IM 12E01B30-02EN

1st Edition : Mar. 08, 2023-00

Appendix Automatic cleaning/Automatic

zero calibration Sequence

n

Automatic cleaning (-A2, -A5)

CLOSE

OPEN

CLOSE

OPEN

Washing

Washing

Meas.

Status

SV2(Wash)

Drainage time

Drainage time

SV4(Drain)

Recovery Meas.

Flow/Calibration

Waiting time

Flow/Calibration

Waiting time

Recovery

1: When Automatic cleaning starts, SV4 (Drain) opens and starts draining the sample out of

the Flow cell.

2: After the “Drainage time” elapses, SV4 closes and sample starts flowing into the detector.
3: After the “Flow/Calibration Waiting time” elapses, SV2 (Wash) opens. Cleaning water (tap

water) starts purging from two water ports on the side of the Flow cell to wash the side or

edge of the Flow cell

4: After the cleaning time elapses, SV4 opens during the Drainage time to wash the Flow cell,

head tank, and the pipes between head tank and the detector.

5: If “Repeat count of wash” is set to over 2, valve working 2 to 4 is repeated.
6: Once the draining for cleaning completes, SV4 closes, and TB830D starts feeding a

sample.

7: After Flow/Calibration Waiting time” elapses, the detector becomes Recovery time.
8: Afthe the Recovery time elapses, a measurement starts.

n

Automatic cleaning (-A3, -A5)

CLOSE

OPEN

CLOSE

OPEN

CLOSE

OPEN

CLOSE

OPEN

Washing

Flow/Calibration

Waiting time Recovery

Washing

Recovery Meas.

Drainage time

Drainage time

Drainage time

Washing

Flow/Calibration

Waiting time

Flow/Calibration

Waiting time

Meas.

Status

SV1(Measure)

SV2(Wash)

SV3(Zero)

SV4(Drain)

1: When Automatic cleaning starts, SV1 (Measure) closes and SV4 (Drain) opens to start

draining the sample out of the Flow cell.

2: After the “Drainage time” elapses, SV4 closes and SV3 (Zero) opens to feed the zero water

into the detector.

3: After the “Flow/Calibration Waiting time” elapses, SV2 (wash) opens. Cleaning water (tap

water) starts purging from two water ports on the side of the Flow cell to wash the side or

edge of the Flow cell.

«
...
76
77
78
79
80
...
»

Содержание TB830D






















































































Отзывы:

Нет отзывов