YOKOGAWA TB830D Скачать руководство пользователя страница 77

Страница: 77 / 85

<9. TROUBLESHOOTING>

9-2

IM 12E04B40-02EN

1st Edition : Mar. 08, 2023-00

Alarm

Number

Name

Explanation

Remedy

NE107

Default

(*1)

NE107

Changed

X54E

Auto Zero cal result

error

Result of auto zero

calibration is out of

range.

Confirm the solenoid valve

runs correctly by manual

operation. Check if the

zero water flows normally.

If no error is found in the

sampling, check whether no

condensation is found on

Measurement window.

Enable

X54F

Auto Cal stability time

limit

Detection value is

not stable during

auto calibration.

Enable

Note : X of Alarm Number denotes Channel of the measurement detection unit.

1: sensor connection number 1-1

5: sensor connection number 2-1

6: sensor connection number 2-2 (not required on the first FD)

(*1): F: Failure, C: Function Check, S: Out of Specification, M: Maintenance required, N: Off

Figure 9.2

TB830D Analyzer Error Message List (Wash)

Alarm

Number

Name

Explanation

Remedy

NE107

Default

(*1)

Error

config.

(HMI)

009E

Auto wash config.

error

Automatic cleaning

is not properly set.

Check automatic cleaning

setting.

Converter setting > Auto wash

> Auto calib. setting

Enable

009F

Disable auto update of

next start

Automatic cleaning/

Automatic zero

calibration is

overdue.

Set the first calibration start

time. Converter setting > Auto

wash> Auto calib. setting

Enable

(*1): F: Failure, C: Function Check, S: Out of Specification, M: Maintenance required, N: Off

9.2

When No Error Indication Appears

There is a possibility that measurement has abnormalities without any error occurrence. Next

table shows some possible causes. Solve the problems referring to the next table.

Figure 9.3

Abnormalities, Their Possible Causes, and Remedies

Abnormalities

Possible Causes

Remedies

Measured value

fluctuates largely.

● Sample air bubble or contamination

stays in Flow cell.

● The measured value fluctuates

according to the sample turbidity.

●

Clean the Flow cell.

●

Check the head tank before the sample

inlet of the detector.

●

Check if the turbidity reading is stable

by using Zero water or Check tool. If the

reading is not stable, identify where the

error occurs in Flow cell, Light source, or

Detector board. After then, bring it to a

normal state.

●

If no error is found in the instrument

or sample flow, set larger value of

measurement time constant.

Measured value

increased over time

● Inside of the Flow cell is contaminated.

● Water droplets or contamination is

adhering to the lenses of the light

source or detection unit.

●

Check the condition of Flow cell,

head tank, piping, lenses. If they are

contaminated, clean them.

●

Check the condition of desiccant

attached inner the cover. Replace it with

new one if deterioration is found.

Measured value

abruptly increases

but plunged in a

short time

● Air bubbles or contamination pass

through the Flow cell.

●

Check the condition of Flow cell,

head tank, piping, lenses. If they are

contaminated, clean them.

●

Turn ON the Air denoising function.

●

Optimize the air denoising parameter.

Содержание TB830D






















































































Результаты поиска

Содержание TB830D

Отзывы:

YOKOGAWA TB830D, Руководство пользователя, Страница: 77 / 85

Результаты поиска

Содержание TB830D

Отзывы: