YOKOGAWA TB830D Скачать руководство пользователя страница 76

Страница: 76 / 85

<9. TROUBLESHOOTING>

9-1

IM 12E04B40-02EN

1st Edition : Mar. 08, 2023-00

9. TROUBLESHOOTING

9.1

When an error occurs

Figure 9.1

TB830D Error List

Alarm

Number

Name

Explanation

Remedy

NE107

Default

(*1)

NE107

Changed

X500

EEPROM error

The TB830D has become defective. Contact

Yokogawa service.

Disable

X501

User param. read error

Disable

X502

Factory param. read error

Disable

X503

AD converter failure

Disable

X504

RAM failure

Disable

X505

Flash Memory failure

Disable

X50A

Sensor communication

error

No sensor is

detected.

Check the power supply

connection.

Check the connection between

the detection unit and the

converter.

Enable

X520

Wash/Cal. box error

Cleaning box does

not work.

Check the connection of Relay

box or configuration (Enable/

Disable.) of the cleaning box.

Disable

X521

Humidity sensor failure Humidity sensor

does not work.

After turning ON/OFF the power,

if the problem still remains,

check the cable connection on

the detector board.

If the cable is correctly

connected, replace the detector

board. When you replace the

detector board, you need to

perform turbidity calibration.

Enable

X522

Lens heater failure

Lens heater shows

abnormal resistivity.

Check the condition of the anti-

fog lens heater.

Check for water leaks to the

lens and disconnection of the

lens heater drive cable. If there

are no abnormalities in these,

the lens heater may have

reached the end of its life.

Contact Yokogawa.

X540

Turbidity High

Turbidity value is

exceeded high limit

setpoint.

Check measurement value.

Confirm Turbidity warning high

limit on sensor setting.

Enable

X541

Turbidity Low

Turbidity value is

less than low limit

setpoint.

Check measurement value.

Confirm Turbidity warning low

limit on Sensor setting.

Enable

X542

Light detection error

Photodetector

current is out of

range.

Check the scattered light current.

Identify where the error occurs

: Flow cell, light source board,

detector board. After then, bring

it back to a normal state.

Enable

X543

Light source failure

Light source intensity

is abnormal.

Check light source monitoring

current and Lightning IF. If value

is abnormal, open the front cover

and check the cable connection

or assemble condition. If the

cause is not found, please

replace the Light source part.

Enable

Note : X of Alarm Number denotes Channel of the measurement detection unit.

1: sensor connection number 1-1

5: sensor connection number 2-1

6: sensor connection number 2-2 (not required on the first FD)

(*1): F: Failure, C: Function Check, S: Out of Specification, M: Maintenance required, N: Off

Содержание TB830D






















































































Результаты поиска

Содержание TB830D

Отзывы:

YOKOGAWA TB830D, Руководство пользователя, Страница: 76 / 85

Результаты поиска

Содержание TB830D

Отзывы: