YOKOGAWA TB830D Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 85

YOKOGAWA TB830D Скачать руководство пользователя страница 74

<8. MAINTENANCE>

8-13

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

8.12 Checking flow rate (liquid level)

Feed sample or zero water to check the liquid level in the FLow cell.
(1) Set converter maintenance mode to On. Remove screw A on the bottom of the detector,

and open the top of the detector (Figure 8.1). Set the status of the valves to a measurement

mode or the zero calibration status (Table 3.1).

(2) Make sure the sample surface is mirror-like as shown in Figure 8.13. When it is undulating,

adjust flow rate of the sample or zero water (see Section 3.5, "Supplying Zero Water",

"Leveling and Adjusting flow rate on detector 3.6", "Supplying sample and Adjusting the

3.12").

(3) Check that the amount of overflowing sample is almost uniformly overflowing around the

entire circumference of the measuring tank. If there is a large deviation, perform leveling

(flow rate adjustment) of the detector in section 3.6, "Leveling and Adjusting flow rate."

(4) Check the contamination of the detector's internal storage and clean it if it is dirty. Be sure to

perform zero calibration and slope calibration after cleaning.

(5) Close detector.

(6) End.

Cnfirm that the measuring

surface is like a mirror finish.

Figure 8.13

Sample surface

8.13 When Sample Water Supply is Cut Off

If the sample or tap water (cleaning water or zero water) stops, normal measurement cannot be

performed. Since the TB830D cannot detect whether the supply of sample, tap water (cleaning

water, zero water) is stopped or not, a periodical check of the line is needed.
Also, when the sample or tap water (cleaning water or zero water) is stopped, an error/alarm may

be detected. Check the supply of sample and tap water when an error/alarm is detected.

«
...
72
73
74
75
76
...
»

Содержание TB830D






















































































Отзывы:

Нет отзывов