YOKOGAWA TB830D Скачать руководство пользователя страница 72

Страница: 72 / 85

<8. MAINTENANCE>

8-11

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

CAUTION

After turning on the power, warm up the instrument for at least 30 minutes before starting the run.

Arrange the following fuses.

Table 8.5

Fuse

Part Number

Product name

Remark

A1633EF

Fuse

Fuse for TB830D x 1

A1624EF

Fuse

1 fuse for relay box (*)

(*)

Two are required for the relay box.

8.11 Replacement of the Silicone Tube

(1) Set converter maintenance mode to On and unclamp the silicone tube.

(2) Open the pinch valve (SV4: solenoid valve).

(3) Remove the silicone tube and thread the new silicone tube through the hole in the pinch

valve (SV4).

(4) Pass the clamp through the silicone tube and insert the upper side into the lower side of the

head tank (it will be easier to insert if it is wet).

(5) Make sure that the drain pipe is visible from the top of the head tank.

(6) Close the clamp.
(7) Place the end of the tube into the drain pipe.

Table 8.6

Silicone tube

Part No.

Product name

Note

K9411JM

Silicone tube

for SV4

CAUTION

•

The pinch valves become hot when energized. The pinch valves are setup to Off

automatically after 10 minutes or more.

•

The valve may not open if no tube is inserted or if the tube is crushed and stuck. If this

happens, assist by hand.

Содержание TB830D






















































































Результаты поиска

Содержание TB830D

Отзывы:

YOKOGAWA TB830D, Руководство пользователя, Страница: 72 / 85

Результаты поиска

Содержание TB830D

Отзывы: