YOKOGAWA TB830D Скачать руководство пользователя страница 61

Страница: 61 / 85

< 7. Calibration >

7-10

IM 12E01B30-02EN

1st Edition : Mar. 08, 2023-00

7.12 Basic (reference) sensitivity calibration

Sensitivity factor(S0) is updated The slope is 100 %. Be sure to perform this calibration after

implementing the Zero calibration.
No error check is conducted at the calibration, therefore, perform calibration properly. For

information on preparation of calibration solution, see “n Formazin Standard Solution”

[How to perform basic (basic (reference)) sensitivity calibration]

(1)  Turn on the maintenance mode.
(2)  Press on   Main screen to enter the calibration menu.
(3)  Select [basic sensitivity calibration] in the menu list of Calibration others.

When a message appears, press [Next]. Enter the concentration of the standard solution

and press [Next].

(4) Check the reading becomes stable. Press [Accept].

(5) Check the calibration result and the concentration of the standard solution, press [Accept] to

update a basic (basic (reference)). Slope is updated to 100%.

(6) To exit the calibration, turn off the maintenance mode after feeding the sample and

confirming that the reading becomes stable.

7.13 Calibration Error

When executing calibration items except for Basic sensitivity calibration, if a calibration result

is abnormal, the calibration error is displayed, and the calibration result is discarded. The

Acceptable range as follows:

Zero:

Acceptable range is wide and hardly error occurs.

Slope:

25 ~ 200%

Zero shift value: -10 ~ 10 NTU
Correction factor: 0.25 ~ 4 times

Содержание TB830D






















































































Результаты поиска

Содержание TB830D

Отзывы:

YOKOGAWA TB830D, Руководство пользователя, Страница: 61 / 85

Результаты поиска

Содержание TB830D

Отзывы: