manualshive.com logo in svg

YOKOGAWA TB830D, Руководство пользователя, Страница: 41 / 85

Поделиться
Скачать
YOKOGAWA TB830D Скачать руководство пользователя страница 41

< 4. SETTING PARAMETERS >

4-6

IM 12E04B40-02EN

1st Edition : Mar. 08, 2023-00

4.2 

Cal./Maint. Settings

4.2.1 

Turbidity value of check tool

Set up the turbidity of the check tool used for slope calibration. The value is set at the factory.

CAUTION

When the initialization is executed, setup data at the factory is deleted. After initialization, re-enter 

the turbidity value of the check tool.

4.2.2 

Zero shift value, Correction factor

These parameters are related to zero shift correction and sensitivity correction in the calibration 

menu. Normally zero shift value is 0, and the correction factor is 1. See “7. CALIBRATION”.

4.2.3 

Stability check

You can configure the following parameters to evaluate the measurement stability in a calibration.

•  Stability check allowable width
•  Stability checking time
•  Stability check limit time

The measurement stability is verified, when the measurement stays within the range of “Stability 

check allowable width” without exceeding the range for longer than the set period of” Stability 

checking time”. If the measurement does not become stable before “Stability check limit time” is 

up, a confirmation dialog appears to abort the calibration.

4.2.4 

Wash/Cal. box

Select whether or not to use Wash Box (Relay box for solenoid valve). While using the Relay box, 

make the Wash box Enabled.
If Wash Box is disabled, you cannot implement automatic cleaning/automatic zero calibration.
If you enable this function when Wash Box is not connected, an alarm occurs to notice the Wash 

Box error.

4.2.5 

Calibration setting others

Zero, slope, Sens.factor Linearize table changed manually. Go to the sensor detail screen to 

check the setting as a reference. These parameters are important for the turbidity linearity.
Do not change those setting except for resetting values.

4.3 

Diagnosis setting

4.3.1 

Light source diagnosis

Select Light source diagnosis On/Off. See 5.3 for details.

4.3.2 

Dried condition diagnosis

Select Dried condition diagnosis On/Off. See 5.3 for details.

Содержание TB830D






















































































Отзывы:

Нет отзывов