YOKOGAWA TB830D Скачать руководство пользователя страница 20

Страница: 20 / 85

<2. INSTALLATION, PIPING, AND WIRING>

2-7

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

L
N
G

Power

(201) L
(202) N
(002) G

Power

Converter

SENCOM

L (101)
N (102)
G (001)

L (101)

N (102)
G (001)

RS485 (-R)

Ethernet (-E)

–
+

–

(61)

(62)

mA1

(65)

(66)

mA2

(81)

(82)

mA3

(85)

(86)

mA4

(21)

(22)

(24)

SHLD (63)

(87)

(88)

SHLD (89)

A+ (91)

−

(92)

GND (93)

SHLD (94)

Termination (95)

Sensor1

Sensor2

(32) NC

(31) C

(33) NO

(42) NC

(41) C

(43) NO

(52) NC

(51) C

(53) NO

(72) NO

(71) C

(73) NC

Power

Supply

Power

Supply

Power

Supply

Analog output (-N2, -N4)

Analog output (-N4)

Contact input (-N2, -N4)

Analog input (-N4)

Contact output

(-WR)

TB830D

Surface scattering turbidity detector

FLXA402T

Liquid Analyzer for Turbidity and Chlorine

L (101)
N (102)
G (001)

L (201)
N (202)
G (003)

L (101)

N (102)
G (001)

Terminal box

L (101)
N (102)
G (001)

L (201)
N (202)
G (003)

L (101)

N (102)

G (001)

Terminal box A

Power supply cable(E)

Power supply cable

TB830D power supply

cable(C)

Power supply cable(E)

FLXA402T power supply cable (B)

SENCOM cable for Turbidity/Chlorine (A)

• If a Relay box is not provided, wire power cable (E) to TB830D.

• If Terminal box A or B is included, wire the power supply cable (E) to the Terminal box.

• wire TB830D power supply cabling (C) between the junction box and TB830D.

Figure 2.6

Wiring TB830D-□-□-NN (without sampling system)

L
N
G

Power

Sensor1

Sensor2

(32)NC

(31)C

(33)NO

(42)NC

(41)C

(43)NO

(52)NC

(51)C

(53)NO

(72)NO

(71)C

(73)NC

RS485(-R)

Ethernet(-E)

Power

Converter

SENCOM

L (101)
N (102)
G (001)

L (201)
N (202)
G (003)

(201) L

(202) N
(002) G

L (101)

N (102)

G (001)

–
+

–

(61)

(62)

mA1

(65)

(66)

mA2

(81)

(82)

mA3

(85)

(86)

mA4

(21)

(22)

(24)

SHLD (63)

(87)

(88)

SHLD (89)

A+ (91)

−

(92)

GND (93)

SHLD (94)

Termination (95)

FLXA402T

Liquid Analyzer for Turbidity and Chlorine

Power

Supply

Terminal box B

TB830D

Surface Scattered Light Turbidity Detector

Analog output (-N2, -N4)

Analog output (-N4)

Contact input

(-N2, -N4)

Analog input (-N4)

Contact output

(-WR)

L (201)
N (202)
G (003)

L (101)

N (102)

G (001)

Power

Supply

Terminal box A

L (101)
N (102)
G (001)

Power supply cable (E)

• Relay box A or B is included.

• wire power supply cable (E) to the junction box.

Figure 2.7

Wiring diagram with sampling system (for-A1)

Содержание TB830D






















































































Результаты поиска

Содержание TB830D

Отзывы:

YOKOGAWA TB830D, Руководство пользователя, Страница: 20 / 85

Результаты поиска

Содержание TB830D

Отзывы: