YOKOGAWA TB830D Скачать руководство пользователя страница 15

Страница: 15 / 85

<2. INSTALLATION, PIPING, AND WIRING>

2-2

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

Installation

See GS12E04B40-01EN for the dimensions of detectors and mounting brackets. For the

converter, see the user’s manual of FLXA402T IM 12A01G01-02EN.
It the sampling system is not provided, it can be wall mounted or pipe mounted.

For wall mounting (Option: / R), mount with 4 M5 screws (not included).

For pipe mounting (Option code: / U), mounting bracket for replacement is available.
See GS 12E04B40-01EN for details.

If the sampling device is provided, fix it to a well-drained concrete foundation with anchor bolts

(M12).

530

Approx. 500

Unit: mm

Approx. 500

550

100

350

Maintenance space

4-ø15 holes

(for M12 Anchor bolts)

Stand

(100)

(20)

490

2.1

Piping

2.1.1

For TB830D-□-□-NN, -A5 (without sampling system)

(1) Sample piping

If the flow rate of the sample is 1.5 to 2 L/min, the sample can be introduced to the detector

as is. Connect the supplied ø33 × ø25 mm black soft vinyl chloride tube to the sample inlet.

However, if the flow rate of the sample exceeds the range of 1.5 to 2 L/min, install a head

tank (constant water level tank) that also serves as a defoaming tank to meet flow rate

requirements. Connect the ø33 × ø25 mm black soft vinyl chloride tube to the pipe between

the head tank and detector.

(2) Drain piping

Connect the supplied ø33 × ø25 mm black soft vinyl chloride tube to the drain port of the

detector.

At this time, install piping with care to prevent accumulation in the tube. Accumulated water

in the drainage pipes may cause problems such as overflow from the detector.

(3) Cleaning water piping

The cleaning water inlet of the detector is sealed with a blind plug.

(Note) When measuring low turbidity (200 NTU or less), prepare a sampling system capable of supplying zero water (filtered tap

water with a zero turbidity filter).

Содержание TB830D






















































































Результаты поиска

Содержание TB830D

Отзывы:

YOKOGAWA TB830D, Руководство пользователя, Страница: 15 / 85

Результаты поиска

Содержание TB830D

Отзывы: