YOKOGAWA TA720 Скачать руководство пользователя страница 61

Страница: 61 / 228

4-2

IM 704510-01E

4.2

Starting/Stopping Measurements

Procedure

SINGLE

START/STOP

Measurement indicator
Illuminates while measurement
is in progress.

Single Measurement

Press the SINGLE key.

Measurement stops after making a single measurement.

To stop the measurement, press START/STOP. If you press the SINGLE key while

measurement is in progress, the measurement is restarted.

Continuous Measurement

• Staring the measurement

Press the START/STOP key.

The measurement indicator turns ON.

• Stopping the measurement

Press START/STOP again.

The measurement indicator turns OFF.

Explanation

Single Measurement

• When block sampling is OFF

Measurement is performed once over the range specified by a single gate (1 block)

and the display of the measurement results is updated.

• When block sampling is ON

Measurement is performed the number of times specified by block size. When the

measurement of all blocks is complete, the display of the measured results is updated.

Continuous Measurement

• When block sampling is OFF

Repeats the single block measurement. When the measurement of a block is

complete, the display of the measured results is updated.

• When block sampling is ON

Repeats the measurement of the specified block size. Each time the measurement of

all blocks is complete, the display of the measured results is updated.

Note

•

Measurement cannot be started when the storage medium is being accessed.

•

For the setup procedure of the gate, see section 6.1.

•

For the setup procedure of turning ON/OFF block sampling and the block size, see section 6.5.

•

If the measurement is stopped in the middle of the measurement block by pressing the

START/STOP key, the measured data up to the point when the key was pressed is acquired,

and the measurement stops.

•

If the measurement conditions are changed while measurement is in progress, measurement

is restarted. Measurement conditions are items that are set mainly by pressing the MODE,

FUNCTION, SAMPLE, and INPUT keys.

•

The CHA/CHB input indicator is provided above the signal input terminal. If this indicator is

not blinking, the signal may not be entering the TA720. Check the trigger level setting (see

section 6.6), the cable connection, and the signal source.

If the CHA/CHB indicator does not blink even when a signal is properly applied to the signal

input terminal of the TA720, it is probably a malfunction. Please contact your nearest

YOKOGAWA dealer as listed on the back cover of this manual for repairs.

Содержание TA720





































































































































































































































Результаты поиска

Содержание TA720

Отзывы:

Похожие инструкции для TA720

Бренды по названию

Популярные бренды

YOKOGAWA TA720, Руководство пользователя

Результаты поиска

Содержание TA720

Отзывы:

Похожие инструкции для TA720

Бренды по названию

Популярные бренды