background image

17

IM 04L55B01-02EN

 

Wiring Procedure

A terminal cover is screwed in place on the I/O terminal block. 

A label indicating the terminal arrangement is affixed to the 

cover.

1.  Turn off the power, and remove the terminal cover.

2.  Connect the signal cables to the terminals.

Recommended 

torque for 

tightening the 

screws

Screw terminal (M3) 0.5 to 0.6 N•m

Clamp terminal

GX90XA: 0.4N•m

GX90XP: 0.4N•m

GX90XD: 0.5N•m

3.  Replace the terminal cover and fasten it with screws. The 

recommended tightening torque for the screws is 0.6 N•m.

Note

With a clamp terminal, if you use a single wire whose 

diameter is 0.3 mm or less, you may not be able to clamp 

the wire securely to the terminal. Take measures to securely 

clamp the wire such as by folding the conductor section that 

will be connected to the clamp terminal in half.

Internal dimensions of the M3 screw 

terminal (unit: mm)

 

6

  0

0.1

Wiring the Clamp Terminal

Wire 

(stripped wire)

Flat blade 

screwdriver

Screw 

terminal

Connection 

port

First, loosen the front screw 

terminal using a flat-blade 

screwdriver.

Insert a wire in the connection 

port, and tighten the screw 

terminal.

Wiring to a GX90XA Analog Input Module

Universal / Low withstand voltage relay / 

Electromagnetic relay / Current (mA) type

Terminal Diagram

 

CH1

301/201/101

101

102

103

113

114

115

310/210/110

M3 screw terminal

Clamp terminal

Wiring direction

CH10

201

202

203

213

214

215

CH1
CH3
CH5
CH7
CH9

CH2
CH4
CH6
CH8

CH10

Wiring direction

Wiring Diagram

1: DC voltage input/DI (level)

2: DI (contact)

+

+

3: TC input

4: RTD input

+

+

B

b

A

A

B

b

5:  DC current input (with an 

external shunt resistor)

6: Current input

+

+

+

+

Type

Input type

Wiring

-U2

DC voltage, DI, thermocouple (TC), 

Resistance temperature detector 

(RTD),  and DC current (by adding an 

external shunt resistor)

1, 2, 3, 4, 5

-C1

DC current (mA)

6

-L1

DC voltage, thermocouple (TC), DI 

(voltage, contact), and DC current (by 

adding an external shunt resistor)

1, 2, 3, 5

-T1

Terminal Arrangement

M3 screw terminal

CH

No.

Term. 

No.

Symbol Term. 

No.

Symbol Term. 

No.

Symbol

CH1

301

b

1

201

-/B

101

+/A

CH2

302

b

1

202

-/B

102

+/A

CH3

303

b

1

203

-/B

103

+/A

CH4

304

b

1

204

-/B

104

+/A

CH5

305

b

1

205

-/B

105

+/A

CH6

306

b

1

206

-/B

106

+/A

CH7

307

b

1

207

-/B

107

+/A

CH8

308

b

1

208

-/B

108

+/A

CH9

309

b

1

209

-/B

109

+/A

CH10

310

b

1

210

-/B

110

+/A

1  There are no symbol indications for the electromagnetic 

relay type, current input type, or low withstand voltage 

relay type.

Содержание SMARTDAC+ GM10

























Отзывы: