YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 56

Страница: 56 / 316

2-40

IM DL950-02EN

One-Shot Output Setup (One shot out Setup)

Tap

One Shot Out Setup

, or press the soft key. The following screen appears.

CAN Frame One-Shot Output (for the 720240 (CAN MONITOR), 720241 (CAN & LIN) modules)

* Can only be set when Frame is set to Data.

Set the message format (STD, XTD).
Set the message ID.
Set the frame (Remote, Data).
Set the data area byte size (0 to 15).*

Set the data.

CAN or CAN FD Frame One-Shot Output (for the 720242 (CAN/CAN FD) module)

* Can only be set when Frame is set to Data.

Set the frame (Remote, Data).

You can set this only when the

message type is CAN.

It is fixed to Data for CAN FD.

Set the message type

(CAN, CAN FD).

Set the message format

(STD, XTD).

Set the message ID.

Set the data area byte size (0 to 15).*

Data*

The number of transmission

data bytes that can be set varies

depending on the message type

and DLC settings.

► Next page

2.9 Configuring the Monitoring of CAN and CAN FD Bus Signals (/VCE option)

Содержание ScopeCorder DL950





























































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL950, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды