YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 46

Страница: 46 / 316

2-30

IM DL950-02EN

Setting Measurement Items (FV Setup)

Tap

FV Setup

, or press the soft key. The following screen appears.

When Performing Frequency or Period Measurements

Turns decelerating prediction on or off

Set the stop prediction (OFF, 1.5, 2, 3, 4, 5, 6, 7, 8, 9, 10).

Set Function to Frequency or Period.

Set the filter (Smoothing, PulseAverage).

When Performing Revolution Measurements

Turns decelerating prediction on or off
Set the stop prediction (OFF, 1.5, 2, 3, 4, 5, 6, 7, 8, 9, 10).

Set the filter (Smoothing, PulseAverage).

Set the pulse and rotate values.

Set Function to Revolution(rpm) or Revolution(rps).

2.7 Configuring Frequency, Revolution, Period, Duty Cycle, Power Supply Frequency, Pulse Width, Pulse

Integration, and Velocity Measurements

Содержание ScopeCorder DL950





























































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL950, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды