YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 38

Страница: 38 / 316

2-22

IM DL950-02EN

Sub Channel Setup (Sub Channel)

Tap

Sub Channel

, or press the soft key. An Sub Channel screen appears.

Set the thermocouple type

(K, E, J, T, L, U, R, S, B, N, W, Au7Fe).

See “Temperature Setup.”

Set the temperature unit (°C, K).

Select a sub channel.

Display settings. ► sec. 2.1

Set input coupling to TC.

Set the display range. ► sec. 2.1

Temperature Setup (Temperature Setup) (RJC, burnout on/off)

Tap

Temperature Setup

, or press the soft key. The following screen appears.

Turns RJC on or off

Turns burnout on or off

Setting the Waveform Vertical and Horizontal Positions (Sliding

the waveform screen)

►

section 2.1

2.4 Configuring Temperature Measurements (For 16-CH temperature/voltage input modules)

Содержание ScopeCorder DL950





























































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL950, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды