YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 262 | Manualshive

Страница: 262 / 316

YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 262

19-16

IM DL950-02EN

19.5 Saving Setup Data

This section explains the following settings for saving setup data: You can save setup data to a file.

Items Common to Scope Mode and Recorder Mode

•  Save destination
•  File name
•  Saving setup data

► “Saving Setup Data (setup)” in the Features Guide

FILE Setup (Save) Menu

1.

On the waveform screen’s

MENU

, tap

FILE

>

FILE

, or press

FILE

.

2.

Tap

Setup

under Save, or press the soft key. The following screen appears.

Select Setup.

Starts saving

Set the file name. ► sec. 19.4

Set the save destination.

► sec. 19.4

Saving Setup Data (Save Execute)

• You can save the setup data (the setup information of each key at the time that the file is saved)

to a file. The extension is .SET.

• The date, time, and communication setup parameters are not saved.
• You cannot save setup data during waveform acquisition. Press START/STOP to stop the

waveform acquisition.

«
...
260
261
262
263
264
...
»

Содержание ScopeCorder DL950





























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды