YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 226

Страница: 226 / 316

16-20

IM DL950-02EN

16.2 Configuring with the All Channel Setup Menu

This section explains how to set the real time math source waveform settings on all channels.

Items Common to Scope Mode and Recorder Mode

•  Turning real time math on and off
•  Label
•  Real time math expression
•  Math source waveforms, coefficients

“Real Time Math (/G03, /G05 option)” in the Features Guide

All Channel Setup Menu

On the waveform screen’s

MENU

, tap

All CH

, or press

ALL CH.

An all channel setup

menu appears.

Tap

RealTime Math

, or press the soft key. The following screen appears.

Set the math source waveform and coefficients.

(The settings vary depending on the expression.)

Turning real time math on or off

Set the label.

Set the expression.

Note

Not all real time math items can be set on the all channel setup menu. For items that cannot be set, use the

real time math menu.

Содержание ScopeCorder DL950





























































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL950, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды