YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 316

YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 162

10-4

IM DL950-02EN

Setting Measurement Items (Item Setup)

4.

Tap

Item Setup

, or press the soft key. The following screen appears.

Select the measurement items that you want to use.

X1: Time value at Cursor1

X2: Time value at Cursor2

ΔX: Difference between the time values of Cursor1 and Cursor2

1/ΔX: Reciprocal of the difference between the time values of Cursor1

and Cursor2

Y1: Vertical value at the intersection of Cursor1 and the waveform

Y2: Vertical value at the intersection of Cursor2 and the waveform

ΔY: Difference in the vertical values at the intersection of

Cursor1/Cursor2 and the waveform

Cursor Value Read Mode

4.

Tap

Other Setup

, or press the soft key.

5.

Tap

Cursor Read Mode

, or press the soft key to set the cursor value read mode.

The two modes available for reading Y1 and Y2 measurements are Display (display data) or
ACQ (acquisition data).
Display: The screen is divided into 1001 parts, and the maximum and minimum values

displayed on those rasters are read.

ACQ:

Measurement data acquired at the sample rate of each waveform is read. When all
traces are selected, measurement data acquired at the sample rate calculated from
T/div and record length is read.

10.2 Measuring with Vertical Cursors

«
...
160
161
162
163
164
...
»

Содержание ScopeCorder DL950





























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды