YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 115

Страница: 115 / 316

4-27

IM DL950-02EN

4.16 Triggering on a Time Trigger in Recorder Mode

This section explains the settings that are used when triggering on a specific date and time in
Recorder mode.

Applicable in Recorder Mode

•  Trigger source
•  Date and time
•  Pre-trigger

► “Pre-Trigger (Pre Trigger)” and “Time Trigger (Time)” in the Features Guide

Trigger Menu

On the waveform screen’s

MENU

, tap

TRIGGER

MENU

, or press

TRIG.MENU

. A trigger

menu appears.

Set the trigger type to Time.

See “Setting the Date

and Time.”

Set the pre-trigger.

Setting the Date and Time (Date/Time Setting)

Press the

Date/Time Setting

soft key. The following screen appears.

Set the date and time.

Confirms the date and time

Содержание ScopeCorder DL950





























































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL950, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды