manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 96

12-2

IM 701210-06E

Loading the Roll Paper

Procedure

1.

Press the PUSH OPEN button and remove the printer cover lock.

Pull up on the handle located on the right side of the printer cover to

open the cover.

2.

Move the release arm, located on the right near the front, to the MAN

FEED position.

Have the inner side of the roll paper (the side that is not glossy)

showing on top and set to the holder.

3.

Insert the edge of the roll paper evenly in the space between the

roller and the black guide, then rotate the paper feed knob away

from you until about 10 cm of the paper is showing from the top of

the roller.

4.

Move the release arm to the FREE position and straighten out the

paper.  Then, move the release arm to the HOLD position.

The printing will fail with an error message, if the release arm is in

the FREE or MAN FEED position during operation.

Printer cover

MAN FEED

Turn the paper 
feed knob

Roll paper

Release arm

Guide

Roller

FREE

HOLD

PUSH OPEN button

MAN FEED

FREE

HOLD

12.1  Loading the Paper Roll and Paper Feeding

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды