YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 64

Страница: 64 / 406

11-26

IM 701210-06E

For Marker Cursors (When Displaying the X-Y Waveform)

MEASURE CURSOR

RESET

SELECT

ALL CH

MODE

POSITION

SIMPLE/ENHANCED

ACQ

START/STOP

SETUP

DISPLAY

ZOOM

DUAL

CAPTURE

HISTORY

MATH

DELAY

MANUAL TRIG

V/DIV

TIME/DIV

TRIGGER

TRIG D

VERTICAL

HORIZONTAL

CAL

X-Y

SEARCH

DSP 1

DSP 2

ENTER

DSP 6

DSP 5

LOGIC A

LOGIC B

EVENT

DSP 3

DSP 4

EXP

GO/NO-GO

ACTION

FILE

SHIFT

Press

CURSOR

Selecting the Cursor Type

Press the

Type

soft key. The cursor type selection menu appears.

Press the

Marker

soft key.

Selecting the Waveform to Be Measured

Press the

Trace

soft key.

If X Axis of the X-Y menu is set to Single, use the

jog shuttle

and

SELECT

select the trace. If X Axis is set to Quad, press the soft key corresponding to the

X-Y waveform (XY1 to XY4) to select the waveform to be measured.

Moving the Cursor

Press the

Position

soft key.

Turn the

jog shuttle

to move Position.

As the cursor is moved, the displayed value of Position changes.

DSP1 to DSP6 are optional.

Note

The marker is displayed for the Y Trace (target Y-axis waveform) specified in the X-Y menu.

11.5 Measuring Waveforms Using Cursors

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды