YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 35

Страница: 35 / 406

10-19

IM 701210-06E

Waveform Computation

Explanation

The following operators can be combined to make computations.

Available Operators

Operator

Setting Example

Description

+,-,*,/

C1+C2

Displays the four arithmetical operations of the two
specified waveform.

SHIFT

SHIFT(C1)

Displays the specified waveform with the phase shifted.

ABS

ABS(M1)

Displays the absolute value of the specified waveform.

SQRT

SQRT(C2)

Displays the square root of the specified waveform.

LOG

LOG(C1)

Displays the logarithm of the specified waveform.

EXP

EXP(C1)

Display the exponent of the specified waveform.

NEG

NEG(C1)

Displays the specified waveform inverted around 0.

SIN

SIN(T)

Displays the sine of the specified waveform.

COS

COS(C1)

Displays the cosine of the specified waveform.

TAN

TAN(C1)

Displays the tangent of the specified waveform.

ATAN

ATAN(C1,C2)

Displays the arc tangent of the two specified waveforms (a
value within

±π

PH(C1,C2)

Displays the phase difference between the two specified
waveforms.

DIF

DIF(C1)

Displays the derivative of the specified waveform.

DDIF

DDIF(C1)

Displays the 2nd order derivative of the specified waveform.

INTG

INTG(C1)

Displays the integral of the specified waveform.

IINTEG

IINTEG(C1)

Displays the double integral of the specified waveform.

BIN

BIN(C1)

Displays the binary computation of the waveform.

P2(C1)

Displays the square of the specified waveform.

P3(C1)

Displays the cube of the specified waveform.

F1(C1,C2)

Displays the

+ C2

of the specified waveform.

F2(C1,C2)

Displays the

– C2

of the specified waveform.

FV(C1)

Displays the inverse of the PWHH of the pulse width.

PWHH

PWHH(M1)

Displays the pulse width computation from the rising edge
to the next rising edge.

PWHL

PWHL(C2)

Displays the pulse width computation from the rising edge
to the next falling edge.

PWLH

PWLH(C1)

Displays the pulse width computation from the falling edge
to the next rising edge.

PWLL

PWLL(C1)

Displays the pulse width computation from the falling edge
to the next falling edge.

PWXX

PWXX(C2)

Displays the pulse width computation from the rising or
falling edge to the next rising or falling edge.

DUTYH

DUTYH(C1)

Positive (high) duty cycle within each cycle of the specified
waveform

DUTHL

DUTYL(C1)

Negative (low) duty cycle within each cycle of the specified
waveform

FILT1

FILT1(C1)

Displays the specified filter after applying a filter.

FILT2

FILT2(C1)

Displays the specified filter after applying a filter.

HLBT

HLBT(C1)

Displays the Hilbert’s transform of the specified waveform.

MEAN

MEAN(C1)

Displays the moving average of the 10th order of the
specified waveform.

LS-

LS-MAG(C1)

Displays the amplitude of the specified waveform’s linear
spectrum.

LS-LOGMAG(C1)

Displays the logarithmic amplitude of the specified
waveform’s linear spectrum.

LS-PHASE(C1)

Displays the phase of the specified waveform’s linear
spectrum.

LS-REAL(C1)

Displays the real part of the specified waveform’s linear
spectrum.

LS-IMAG(C1)

Displays the imaginary part of the specified waveform’s
linear spectrum.

PS-

PS-MAG(C1)

Displays the amplitude of the specified waveform’s power
spectrum.

PS-LOGMAG(C1)

Displays the logarithmic amplitude of the specified
waveform’s power spectrum.

10.5 User-Defined Computation (Optional)

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды