manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 297

19-9

IM 701210-06E

Specifications

19

19.7 Storage

Built-in Storage
• Floppy Disk Drive

Item

Specifications

Number of drives

1

Size

3.5 inch

Capacity

720 KB or 1.44 MB

• Zip Drive (DL750 Only)

Item

Specifications

Number of drives

1

Capacity

100 MB or 250 MB

• PC Card Interface

Item

Specifications

Number of drives

1

Maximum capacity

5 GB

Supported cards

Flash ATA memory card (PC card TYPE II) PC card type, CF card + adapter card, and HDD PC
card.

For details on the compatible cards, contact your nearest YOKOGAWA dealer.

Internal Hard Disk (Optional)

Item

Specifications

Number of drives

1

Size

2.5 inch

HDD capacity used

30 GB, FAT32, 2 partitions by factory default

File name

Supports long file names (ANK16 characters)

Function

Mount the internal HD via the SCSI port

External Storage Interface
• SCSI

Item

Specifications

Standard

SCSI (Small Computer System Interface).ANSIX3.131-1986

Connector

Half pitch 50 pins

Connector pin assignment Unbalanced (single-ended)

USB Storage Device*

Item

Specifications

Compatible USB mass

USB (USB Mass Storage Class) hard disk drive, MO disk drive, and flash memory

storage devices

For specification details, see the next section, "USB PERIPHERAL Interface."

* Model that can connect a USB storage device

 • DL750:

Check the overview screen by choosing MISC > Overview.
If USB Storage: Yes and Soft Version: 6.02 (or later) are displayed, a USB storage device can be connected.

 • DL750P: All DL750Ps can connect to a USB storage device.

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды