manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 29

10-13

IM 701210-06E

Waveform Computation

10

Explanation

The phase of CH1 to CH16, DSP1 to DSP6 (optional), and Math1 to Math7 waveforms

can be displayed with the phase shifted.  Computation can also be performed on phase-

shifted waveforms.

Setting the Computation Range: Start Point/End Point

By default, the measurement range is 

±

5 divisions of the display frame on the time axis.

You can limit this range.

The concept of the computation range is analogous to the concept of the selectable

range of cursor display position in cursor measurement.

For details, see section 11.5, “Selectable Range of Cursor Position.”

Allowable Shift Range

The phase can be shifted in the following range.

 • When the Time Base Is Set to Internal Clock

Selectable range:

Time value of –(record length/2) to (record length/2)

Resolution:

1/sample rate

The sample rate varies depending on the record length or T/div setting. For details,

see appendix 1, "Relationship between the Time Axis Setting, Sample Rate and

Record Length."

 • When the Time Base Is Set to External Clock

Selectable range:

–(record length/2) to (record length/2)

Resolution:

1

When a Waveform That Results by Offsetting the CH1 Waveform by 5 ms Is Set to

Math1

 • Phase Shift CH1:

5 ms

 • Math1

Operation: Shift (S1)

Source1:

CH1

5 ms

Linear Scaling

When performing computation on a channel that has linear scaling set, the computation

is performed on the scaled value.

Notes when Performing Computation

Computation is not performed again when you change Start Point or End Point while

computation is stopped. Be sure to press the Exec soft key to perform the computation

again. Otherwise, the waveform will not be displayed correctly when the screen is redrawn.

Note

While computation is in execution, 

 is displayed at the upper left corner of the screen.

10.4 Phase-Shifted Display

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды