manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 230

16-19

IM 701210-06E

Ethernet Interface (Optional)

16

16.5 Sending E-mail Messages (Periodic Mail or Action Mail)

Action Mail

Information such as the trigger time can be sent to a specified mail address on the

network as an action of action-on-trigger or GO/NO-GO determination.

• DL750/DL750P Information That Is Transmitted

• Acquisition Condition

Start/Stop, acquisition counter

• Trigger Time

• Success/Fail Information of GO/NO-GO

Only when GO/NO-GO determination is executed (see sections 11.8 and 11.9).

• Results of Waveform Parameter Measurement

Only when automated measurement of waveform parameters (see section 11.6) or

GO/NO-GO determination using waveform parameters (see section 11.8) is

executed.

• Fail Cause

Only when GO/NO-GO determination is executed (see sections 11.8 and 11.9).

• Sample Action Mail

[Comment]   aaaaaa

[ACQ Status]    Stopped    1

[Trigger Date and Time]    2002/06/17    17:28:59.38

[GO/NOGO Status]    Success: 9    Fail: 1

[NOGO Factor]    Param4(Ch4,tWd )

Max (C1)   4.16667V

SDv (C2)   697.941mV

Freq(C3)   500.0000kHz

+Wd (C4)   1.00us>

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды