manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 212

16-1

IM 701210-06E

Ethernet Interface (Optional)

16

Chapter 16

Ethernet Interface (Optional)

16.1 Connecting the DL750/DL750P to the Network

<For a description of this function, refer to page 2-59.>

Ethernet Interface Specifications

A 100BASE-TX port is provided on the left side panel of the DL750/DL750P.

Item

Specifications

Number of communication ports

1

Electrical and mechanical specifications

Conforms to IEEE802.3

Transmission system

Ethernet (100BASE-TX/10BASE-T)

Transmission rate

100 Mbps max.

Communication protocol

TCP/IP

Supported services

FTP server, FTP client (network drive), LPR client
(network printer), SMTP client (mail transmission),
DHCP, DNS, and Web server

Connector type

RJ-45 connector

ETHERNET 100BASE-TX port

RJ-45 modular jack

100B

ASE-TX

LINK

AC
T

ACT LED
Blinks when packet transmission is being 
carried out normally.

LINK LED
Illuminates when the link between the 
port on the DL750/DL750P and the 
connected device is established and 
communication is mutually possible.

Items Necessary for Connection

Cable

Be sure to use one the following cables for connection.

• UTP (Unshielded Twisted-Pair) cable (category 5 or better)

• STP (Shielded Twisted-Pair) cable (category 5 or better)

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды