YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 126

Страница: 126 / 406

13-13

IM 701210-06E

Saving and Loading Data

Explanation

Formatting a Floppy Disk

When using a new floppy disk, you must format it. Select the format that is appropriate

for the floppy disk that you are using from below.

• 2DD 720K

Formats a 2DD floppy disk to 720 KB/9 sectors.

• 2HD 1.44M

Formats a 2HD floppy disk to 1.44 MB/18 sectors.

Formatting a Zip Disk, PC Card, or USB Storage Device

When using a new Zip disk, you need to format it.

The format for 250 MB and 100 MB disks is as follows:

FDISK 1 partition

Flash ATA cards are formatted to IBM-compatible format.

2GB or more:

FAT32

Less than 2GB:

FAT16

Formatting an External SCSI Device

The formats of the disk that are connected via the SCSI (option) are as follows:

• MO

Semi-IBM format. Handled as a removable disk.

• Zip

FDISK 1 partition. Handled as a fixed disk.

Formatting the Internal Hard Disk (Optional)

• Selecting the Number of Partitions

You can set the number of partitions to 2 or 3.

• Setting the Realtime Recording Area

You can set the realtime recording area to 30%, 40%, 50%, 60%, or 70% of the entire

capacity of the internal hard disk. The default value is 50%.

Selecting the Number of Partitions

You can set partitions on the internal hard disk (optional) and some of the external SCSI

devices. However, partitions cannot be specified on removable disks. You can select

the number of partitions from 1 to 3 (2 or 3 on the internal hard disk).

13.5 Formatting the Storage Medium

Содержание ScopeCorder DL750























































































































































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL750

Отзывы:

Бренды по названию

Популярные бренды