YOKOGAWA RC400G Скачать руководство пользователя страница 97

Страница: 97 / 141

<7. Calibration>

7-2

IM 12F4A1-01E

(4) Re-mount the electrode mechanism block to the measuring tank.

Also, press [CELL] key to rotate the indicator electrode.

7.2.2

Zero Calibration Using Chlorine-Free Water

Conduct zero calibration using the chlorine-free water in the following procedure: Mount the

electrode mechanism block to the measuring tank and turn the indicator electrode in advance.
(1) Prepare chlorine-free water of approx. 2 to 3 liter produced by passing sample water

through activated charcoal filter in a suitable vessel.

Also prepare a tube (O.D. 6 mm x I.D. 4 mm) for supplying this chlorine-water to the residual

chlorine analyzer.

(2) Set the vessel containing chlorine-free water so that the water level satisfies the conditions

shown in Figure 7.1.

Chlorine-free water

35 cm or less

50 cm

Maximum level

Reagent metering pump

center position

Residual chlorine analyzer

installation surface

F7.1.ai

Figure 7.1

Chlorine-Free Water Level

(3) Connect one end of the tube for supplying chlorine-free water to the residual chlorine

analyzer standard solution tubing connecting port (Rc1/4 screw). Immerse the opposite end

of the tube in chlorine-free water.

(4) Transfer the “sample water/standard solution” selector valve to the “standard solution”

position and feed the detector with chlorine-free water.

The measured value normally stabilizes in approx. 5 to 10 min.

(5) Confirm that the mode is <MAINT.> and set the function code to “1”.

The content of this code is “zero calibration”.

(6) Start calibrating operation. Press [ENT] key.

During calibrating operation, <CAL> lamp flashes. Calibration is performed when the

analyzer stabilizes to that predetermined conditions are met after measured value stability is

automatically checked.

When calibration is executed, the value displayed in the data display flashes once and, at

the same time, flashing <CAL> lamp extinguishes.

After calibration, pass chlorine-free water for short period of time and confirm that indication

holds the value of 0 ppm stably.

(7) Now the zero calibration is completed.

Leave the tube for supplying chlorine-free water as connected and subsequently conduct

span calibration.

14th Edition : Jul. 15, 2020

Содержание RC400G














































































































































Результаты поиска

Содержание RC400G

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA RC400G, Руководство пользователя

Результаты поиска

Содержание RC400G

Отзывы:

Бренды по названию

Популярные бренды