YOKOGAWA RC400G Скачать руководство пользователя страница 105

Страница: 105 / 141

<8. Maintenance>

8-4

IM 12F4A1-01E

Metering pump mounting screws (4 screws)

Pump mounting plate

Pump main body

Transparent plate mounting screws

Piston

Transparent plate

Retainer mounting screw

“Bellofram”

Retainer

Ring

O-ring

Valve assembly

F8.2.ai

Figure 8.2

Metering Pump Construction

8.7.1

“Bellofram” Replacement

Perform “Bellofram” replacement work using the following procedure:
(1) Press [PUMP] key to stop metering pump operation. Take measures to prevent reagent

from flowing out of the reagent tank.

(2) Remove the transparent plate of the metering pump.

Loosen four screws located on the front face.

(3) Remove the ring which forces the “Bellofram” flange down.
(4) Remove the retainer fixed to the piston with screw.

(5) Remove the “Bellofram” which has been used and mount a new “Bellofram”.

For mounting, first press the “Bellofram” flange using the ring. Fold the “Bellofram” so as to

cover the piston using the attached jig (see Figure 8.3).

(1)

(2)

“Bellofram”

Ring

Pump main body

Piston

“Bellofram” mounting jig

F8.3.ai

Figure 8.3

“Bellofram” Mounting Procedure

(6) Reassemble the disassembled parts.

14th Edition : Jul. 15, 2020

Содержание RC400G














































































































































Результаты поиска

Содержание RC400G

Отзывы:

Похожие инструкции для RC400G

Бренды по названию

Популярные бренды

YOKOGAWA RC400G, Руководство пользователя

Результаты поиска

Содержание RC400G

Отзывы:

Похожие инструкции для RC400G

Бренды по названию

Популярные бренды