YOKOGAWA RC400G Скачать руководство пользователя страница 10

Страница: 10 / 141

<1. Outline>

1-1

IM 12F4A1-01E

1. Outline

In chlorinated tap water and industrial water, the chlorination effect can be determined by

measuring residual chlorine contact.
The RC400G Residual Chlorine Analyzer is for process use and employs rotating

electrode polarography as its measuring principle.
It can be used for continuous measurement of residual chlorine composed of free

available chlorine and combined available chlorine or for free available chlorine only.

The

RC400G Residual Chlorine Analyzer includes “Tap Water type (Model RC400G-1)”

suitable for measurement of tap water or filtered water, “Raw Water type (Model

RC400G-2)” suitable for measurement of raw water and “Treated Water type (Model

RC400G-3)” suitable for measurement of treated water such as sewer water after

secondary treatment or plant waste water.

Combined Chlorine Insensitive Version

If raw water contains large quantities of ammonia nitrogen, combined chlorine will form

and remain in the reaction process even if necessary and sufficient chlorine is added at

prechlorination point. In particular, when the pH and temperature of the water are low, combined

chlorine (dichloramine) remains longer and breaks down slowly.
In measurement of free available chlorine in sample water that contains a high concentration of

combined chlorine, measurement errors may occur when the previous model of residual chlorine

analyzer is used. To solve this problem the combined chlorine insensitive version should be used.

It has modified electrode and reagent composition, thereby improving sensitivity to free available

chlorine in the presence of combined chlorine. The electrode configuration, reagent composition

and applied voltage have been changed, otherwise, the measurement principle, equipment,

specifications and performance remain unchanged from the previous model.

In this chapter, the operating principle and structural outline of the RC400G Residual Chlorine

Analyzer is described.

F1.1E.ai

Converter

Detector

Metering pump

Front

Side

Back

Figure 1.1

Appearance of RC400G Residual Chlorine Analyzer (RC400G-1, Tap Water type)

14th Edition : Jul. 15, 2020

Содержание RC400G














































































































































Результаты поиска

Содержание RC400G

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA RC400G, Руководство пользователя

Результаты поиска

Содержание RC400G

Отзывы:

Бренды по названию

Популярные бренды