YOKOGAWA PX8000 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 202

background image

15-1

IM PX8000-02EN

15.1 Performing Addition, Subtraction,

Multiplication, and Division

This section explains the following settings for performing addition, subtraction, multiplication, and
division.
• Computation
Operator (+, –, *, /), computation source waveform, unit, label, turning the waveform display on and

off

• Scaling
Math waveform to scale (computed waveform), scaling mode, upper and lower limits of the display

range

• Computation start and end points

►

Features Guide: “Basic Arithmetic (S1+S2, S1-S2, S1*S2, and S1/S2)”

“Scaling Mode (Scaling Mode)”

“Record Length (Record Length)”

MATH Menu

Press

MATH

to display the following menu.

Set the computation.

• Select the Math waveform (computed waveform) to scale (1-8).

• Set the upper and lower limits of the display range

(−9.9999E+30-9.9999E+30).

Set this when the scaling mode is Manual.

• Set the scaling mode (Auto, Manual).

Set the scaling.

Set the computation start and end points (−5div to 5div).

The setting resolution varies depending on the display record length.

The end point must be greater than or equal to the start point.

Note that there is a limitation in the number of data points that is used

depending on the number of equations to be computed.

Not all the data points may be used.

Set Mode to ON.

Configuring Computations (Math Setup)

1.

Press the

Math Setup

soft key.

2.

Press a soft key from

Math1

to

Math8

to display the following screen.

Select the operation (S1+S2, S1–S2, S1*S2, S1/S2).

Turns the waveform display on and off

Set the label.

Set the unit.

Select the computation source waveform

(U1-U4, I1-I4, P1-P4, AUX3-AUX8, Math1-Math7).

Chapter 15 Waveform Computation

«
...
114
115
116
117
118
...
»

Содержание PX8000











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PX8000

Бренд: 2B Technologies Страницы: 4

Бренд: TA Instruments Страницы: 7

Бренд: Velleman Страницы: 96

Бренд: Emos Страницы: 76

Бренд: Hanna Instruments Страницы: 52

Recordall Series

Бренд: Badger Meter Страницы: 8

Бренд: Obvius Страницы: 15

Бренд: wtw Страницы: 72

Бренд: GasQuip Страницы: 8

Бренд: ICP DAS USA Страницы: 340

ENERGY MAX EM400

Бренд: Molectron Страницы: 40

Бренд: Bamo Страницы: 2

Druck DryTC 165

Бренд: Baker Hughes Страницы: 130

Бренд: Zico Страницы: 3

Бренд: Hach Страницы: 252

ISOLGUARD HIG93

Бренд: hakel Страницы: 15

Blackbird OECD MDE0835

Бренд: fos4X Страницы: 80

Бренд: Caird Technology Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды