YOKOGAWA IM XL100C-E, Руководство пользователя

Страница: 91 / 134

5-31
IM XL100C-E
1
2
3
4
5
6
7
App
Index
Standard Protocol
EV Saves the manual sampled data
or screen image data to the
storage medium
Syntax EV p1<terminator>
p1 Operation type
Saves manual sampled data to the storage
medium: 0
Saves screen image data to the storage
medium: 2
Reserved: 1 , 3 , 4
Example Saves manual sampled data to the storage
medium.
EV 1
Description • Data cannot be saved while logging.
• Parameter p1 cannot be set to 0 while the
storage medium is being formatted or while
data is being saved to the storage medium.
LO Loads the setup data
Syntax LO p1 <terminator>
p1 Path name (up to 150 characters)
Setting memory: /SETMEMORY/file name
(excluding the extension)
Internal memory: /INTERNALMEMORY/file
name (excluding the extension)
CF memory card: /CFCARD/file name
(excluding the extension)
SD memory card: /SDCARD/file name
(excluding the extension)
Example Load the setting data of setup file SETFILE1
(.SET extension) from the setting memory.
LO /SETMEMORY/SETFILE1
Description • This command is the same as the YO
command. To apply the functions of the basic
setting commands, the settings must be
saved using the XE command.
• This command can be issued only when the
path is specified and the corresponding
storage medium is inserted.
LI Saves the setting data
Syntax
LI p1 <terminator>
p1
Path name (up to 150 characters)
Setting memory: /SETMEMORY/file name
(excluding the extension)
Internal memory: /INTERNALMEMORY/file
name (excluding the extension)
CF memory card: /CFCARD/file name
(excluding the extension)
SD memory card: /SDCARD/file name
(excluding the extension)
Example Save the setting data to a file named SETFILE2
on the CF memory card.
LI /CFCARD/SETFILE2
Description • A “.SET” extension is attached to the saved
file. This command is equivalent to the YI
command.
• The settings are not saved with this command
if an external storage media error occurs such
as the external storage medium not inserted
at the save destination.
CM Sets the communication input
data
Syntax
CM p1,p2<terminator>
p1
Communication input data number
C01
to
C32
(same as CO01 to CO32)
CO01
to
CO32
p2
Communication input data
Selectable range:
-9.9999E+29
to
-
1.0000E- 30
,
0
,
1.0000E-30
to
-9.9999E+29
(The + sign of “E+” can
be omitted.)
Query
CM?
Example Set 1.0000E-10 to communication input data
number CO01.
CM CO01,1.0000E-10
EM Starts/stops the e-mail
transmission function
Syntax
M p1<terminator>
p1
Operation type
Start:
0
Stop:
1
Example Start the e-mail transmission function.
EM 0
Description To use the e-mail transmission function, you
must set the Ethernet interface, e-mail address,
and contents to be transmitted. For the
procedure to set each item, see section 2.11
“Setting the E-mail Transmission function”.
KE Key operation command
Syntax KE p1<terminator>
p1 Key type
ESC key: ESC
HOME key: HOME
REVIEW key: REVIEW
FILE key: FILE
SETTING key: SETTING
HOLD key (hold down): LONGHOLD
TIME/DIV left key: TIMEDIVSHORT
TIME/DIV right key: TIMEDIVLONG
RANGE key: RANGE
SAVE key: SAVE
DISPLAY key: DISP
5.6 Setting Commands (Control)