YOKOGAWA FA-M3V e-RT3 Plus Скачать руководство пользователя страница 161

Страница: 161 / 274

A3-1

IM 34M06C11-01E

A3.

Installation and Wiring

A3.1

Environmental Conditions for Installation

within a Panel Enclosure

Refer to the following considerations when designing the interior of the panel enclosure

to ensure operability, maintainability, and environmental durability.
Figure A3.1 shows a typical example of a layout within a panel enclosure.



Temperature Considerations

- Provide good ventilation to prevent heat from being trapped inside the panel

enclosure. If two or more FA-M3 controller units are installed vertically within the

same panel enclosure, provide a clearance of at least 8cm between them.

- Ensure that the upper and lower vents near the FA-M3 controller are not blocked

either by wiring or otherwise.

- Avoid mounting the controller directly above any equipment that generate large

amounts of heat.

- If there will be times where the temperature inside the panel enclosure reaches

55°C (131°F) or higher, use a fan or an air conditioner for cooling. Consider

providing a safety mechanism such as a temperature sensor inside the panel

enclosure to raise an alarm upon failure of the fan or air conditioner as such failures

may adversely affect the system. Conversely, if temperature is likely to fall below

0°C (32°F) during morning startup, include a small heater, lamp, or other heat

source to preheat the panel enclosure.

Figure A3.2 shows examples of cooling systems.



Humidity Considerations

Condensation may occur due to sudden temperature changes resulting from the turning

on and off of an air conditioner. If condensation occurs on any of the circuit boards, the

instrument may malfunction due to shorted internal circuitry. If there is a risk of

condensation, either keep the power turned on at all times, or use a space heater or

other alternative means to keep the controller constantly preheated.



Vibration and Shock Considerations

- As a countermeasure to keep shock or vibration below the specified limit, place the

panel enclosure as far away as possible from any source of vibration or shock, or

place the panel enclosure on vibration-proof rubber.

- As a countermeasure to keep mechanical shock from electromagnetic switches

mounted inside the panel enclosure below the specified limits, install such devices

on vibration-proof rubber.

Note

Be wary of any vibration and shock to the hard disk module.
Any mechanical vibration or shock occurring during transportation of equipment or

facilities into which the FA-M3 has been assembled must also be within the

specifications limits. The specification range for vibration and shock is especially

stringent for the hard disk module, as compared to other modules. When transporting,

use the same packaging in which the product was originally shipped.

Содержание FA-M3V e-RT3 Plus



















































































































































































































































































Результаты поиска

Содержание FA-M3V e-RT3 Plus

Отзывы:

Похожие инструкции для FA-M3V e-RT3 Plus

Бренды по названию

Популярные бренды

YOKOGAWA FA-M3V e-RT3 Plus, Руководство по оборудованию

Результаты поиска

Содержание FA-M3V e-RT3 Plus

Отзывы:

Похожие инструкции для FA-M3V e-RT3 Plus

Бренды по названию

Популярные бренды