manualshive.com logo in svg

YOKOGAWA EXAxt ZR22G, Руководство пользователя, Страница: 71 / 211

Поделиться
Скачать
YOKOGAWA EXAxt ZR22G Скачать руководство пользователя страница 71

 

 

<4.  Piping>

4-6

IM 11M12A01-02E 16th Edition : Mar. 19, 2020-00

4.2.1  

Piping Parts for System 2

Check that the parts listed in Table 4.2 are ready.

Table 4.2 

Piping Parts

Detector 

Piping location 

Parts Name 

Note

General use 

detector 

Calibration gas 

inlet 

Stop valve or check valve  Recommended by YOKOGAWA (L9852CB 

or G7016XH) Provided by YOKOGAWA

(K9292DN or K9292DS)

Nipple * 

Rc 1/4 or 1/4 NPT 

General parts

Zero gas cylinder 

User´s scope 

Pressure reducing valve

Recommended by YOKOGAWA 

(G7013XF or G7014XF) 

Joint for tube connection 

Rc 1/4 or 1/4 NPT 

General parts 

Reference gas 

inlet 

Air set 

Recommended by YOKOGAWA 

(G7003XF/K9473XK or G7004XF/K9473XG) 

Joint for tube connection 

Rc 1/4 or 1/4 NPT 

General parts

High temperature 

Detector 

(0.15 m) 

Calibration gas 

inlet 

Stop valve or check valve  Recommended by YOKOGAWA (L9852CB 

or G7016XH) Provided by YOKOGAWA 

(K9292DN or K9292DS) 

Nipple * 

Rc 1/4 or 1/4 NPT 

General parts 

Zero gas cylinder 

User´s scope 

Pressure reducing valve 

Recommended by YOKOGAWA

(G7013XF or G7014XF) 

Joint for tube connection 

Rc 1/8 or 1/8 NPT 

Reference gas 

inlet 

Air set 

Recommended by YOKOGAWA 

(G7003XF/K9473XK or G7004XF/K9473XG) 

Joint for tube connection 

Rc 1/4 or 1/4 NPT 

General parts 

Sample gas 

outlet 

Ejector assembly * 

Recommended by YOKOGAWA (E7046EC 

or E7046EN) 

T-shaped joint of the same  

diameter * 

R 1/4 or 1/4 NPT 

General parts 

Needle valve * 

Rc 1/4 or 1/4 NPT 

General parts 

Nipple of other diameter *  R 1/2 to R 1/4 

or R 1/2 to 1/4 NPT

General parts 

Note:   Parts with marking * are used when required. 

General parts can be found on the local market.

4.2.2  

Piping for the Calibration Gas

This piping is to be installed between the zero gas cylinder and the ZA8F flow setting unit, and 

between the ZA8F flow setting unit and the ZR22G detector.

The cylinder should be placed in a case assemble E7044KF or the like to avoid any direct 

sunlight or radiant heat so that the gas cylinder temperature does not exceed 40

°

C. 

Mount a reducing valve (specified by YOKOGAWA) on the cylinder.
Mount a check valve or stop valve (specified by YOKOGAWA) on the nipple (found on the local 

market) at the calibration gas inlet of the detector as illustrated in Figure 4.8.  

(The check valve or the stop valve may have been mounted on the detector when shipped.) 

Connect the flow setting unit and the detector to a stainless steel pipe 6 mm (O.D.) x 4 mm or 

larger (I.D.) (or nominal size 1/4 inch).

Содержание EXAxt ZR22G




















































































































































































































Отзывы:

Нет отзывов