manualshive.com logo in svg

YOKOGAWA EXAxt ZR22G, Руководство пользователя, Страница: 119 / 211

Поделиться
Скачать
YOKOGAWA EXAxt ZR22G Скачать руководство пользователя страница 119

 

 

<8.  Detailed Data Setting>

8-6

IM 11M12A01-02E 16th Edition : Mar. 19, 2020-00

8.2.3 

Output Hold Setting

To set the output hold, follow these steps:
(1)  Press the [Setup] key in the Basic panel display to display the Execution/Setup display. 

Then select “Commissioning” in the Execution/Setup display. Next, select the “mA-output 

setup” and then the “mA-outputs presets” display as shown in Figure 8.2.

      Warm up:        4mA

   Preset value:     4 . 0 mA

 Maintenance:  Hold

   Preset value:     4 . 0 mA

 Cal.blow back:  Hold

   Preset value:     4 . 0 mA

 Error:               Preset

   Preset value:     3 . 4 mA

Enter

mA-outputs presets

F8.1E.ai

 

      Warm up:        4mA

    Preset value:     4 . 0 mA

  Maintenance:  Hold

    Preset value:     4.0mA

  Cal.blow back:  Hold

    Preset value:     4 . 0 mA

  Error:               Preset

    Preset value:     3 . 4 mA

Enter

mA-outputs presets

Non-Hold

Hold

Preset

F8.2E.aiS

Figure 8.1 

mA-outputs presets Display  

Figure 8.2 

Selecting Maintenance

(2)  From this display (Fig. 8.2), select the desired display. Figure 8.3 shows an example 

of selecting “Maintenance”. Select the desired output status.

(3)  If a preset value is selected, set the corresponding output current. If you select a preset 

value just below Maintenance on the screen, the numeric-data entry display will appear. 

Enter the current value you want. To set 10 mA, type in 010 and press the [Enter] key to 

complete the setting. The setting range is from 2.4 to 21.6 mA.

NOTE

“Error” of mA-outputs presets is not displayed when option code “/C2” or “/C3” (NAMUR NE 43 

compliant) is specified.

8.2.4 

Default Values

When the analyzer is delivered, or if data are initialized, output hold is the default as shown in 

Table 8.3.

Table 8.3 

Output Hold Default Values

Status 

Output hold setting

Preset value

During warm-up 

4 mA

4 mA

Under maintenance 

Holds output at value just before maintenance started.

4 mA

Under calibration or blow back  Holds output at value just before starting calibration or 

blow back.

4 mA

On Error occurrence 

Holds output at a preset value.

3.4 mA

8.3 

Alarms Setting

The analyzer enables the setting of four alarms — high-high, high, low, and low-low alarms 

— depending upon the measurement conditions. The following section sets out the alarm 

operations and setting procedures.

Содержание EXAxt ZR22G




















































































































































































































Отзывы:

Нет отзывов