YOKOGAWA EXA DO402G Скачать руководство пользователя страница 69

Страница: 69 / 95

<6. Calibration Procesure>

6-2

IM 12J05D02-01E

Manual calibration

This is a calibration method whereby the sensor is not exposed to a calibration fluid, but

is calibrated by comparison with a reference method. This reference method is normally a

laboratory analysis of the water sample: either by iodometric titration according ISO 5813 or an

electrochemical method according ISO 5814.
The calibration is done in MAN.CAL mode in maintenance level.

NOTE

Calibration must be carried out after changing the manual pressure setting (see service code 51).
When the manual pressure is enabled, air and water calibrations are made based on the

specified pressure.
M.PR.ON YES/NO is displayed before the calibration to confirm whether the calibration will be

made based on the pressure.

6.1.2

Diagnostic functions performed during calibration

The calibration is a semi-automatic calibration, which means that the sensor output is used for

calculation of sensor parameters after the readings have stabilized. The criteria for stabilization

are set in service code 20. If stable readings are not achieved within one hour error E1 message

will appear on the display and the procedure is aborted. The calculated sensor parameters are

compared with preset tolerances and if these conditions are not met, Error E2 (Zero Error) or E3

(Slope Error) will be signalled.

NOTE

1. Error messages that appear initially indicate inadequate settings of the diagnostic variables

in service codes 01, 20 and/or 22.

2. Patience improves the accuracy of calibration. When the EXA prompts the user that the

preset criteria are met by showing CAL.END message it only means that the minimum

criteria are met. When the signal still changes after this initial acceptance, EXA will

automatically update the sensor characteristics with the new information.

6.2

Calibration procedure using air calibration

method

6.2.1 Preparation

Move the sensor to a maintenance site and wash off any dirt on the membrane. Lightly wipe off

any remaining water from the membrane with a soft tissue.
Expose the sensor to the air in an environment where there is no temperature change and no

wind. (A convenient way to accomplish this environment is to place the sensor in an empty

bucket)

NOTE

If sensors are used without temperature compensating element, the temperature must be

adjusted to ambient temperature in service code 13.

Before zero calibration, see 6.3.1 Preparation

9th Edition: Aug. 05, 2015-00

Содержание EXA DO402G
































































































Результаты поиска

Содержание EXA DO402G

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA EXA DO402G, Руководство пользователя

Результаты поиска

Содержание EXA DO402G

Отзывы:

Бренды по названию

Популярные бренды