YOKOGAWA EXA DO402G Скачать руководство пользователя

Страница: 3 / 95

IM 12J05D02-01E

Safety Precautions

Safety, Protection, and Modification of the Product

• In order to protect the system controlled by the product and the product itself and ensure

safe operation, observe the safety precautions described in this user’s manual. We assume

no liability for safety if users fail to observe these instructions when operating the product.

• If this instrument is used in a manner not specified in this user’s manual, the protection

provided by this instrument may be impaired.

• If any protection or safety circuit is required for the system controlled by the product or for

the product itself, prepare it separately.

• Be sure to use the spare parts approved by Yokogawa Electric Corporation (hereafter

simply referred to as YOKOGAWA) when replacing parts or consumables.

• Modification of the product is strictly prohibited.
• The following safety symbols are used on the product as well as in this manual.

WARNING

This symbol indicates that an operator must follow the instructions laid out in this manual in order

to avoid the risks, for the human body, of injury, electric shock, or fatalities. The manual describes

what special care the operator must take to avoid such risks.

CAUTION

This symbol indicates that the operator must refer to the instructions in this manual in order to

prevent the instrument (hardware) or software from being damaged, or a system failure from

occurring.

CAUTION

This symbol gives information essential for understanding the operations and functions.

NOTE

This symbol indicates information that complements the present topic.

This symbol indicates Protective Ground Terminal.

This symbol indicates Function Ground Terminal. Do not use this terminal as the protective

ground terminal.

Notes on Handling User’s Manuals

• Please hand over the user’s manuals to your end users so that they can keep the user’s

manuals on hand for convenient reference.

• Please read the information thoroughly before using the product.
• The purpose of these user’s manuals is not to warrant that the product is well suited to any

particular purpose but rather to describe the functional details of the product.

• No part of the user’s manuals may be transferred or reproduced without prior written

consent from YOKOGAWA.

• YOKOGAWA reserves the right to make improvements in the user’s manuals and product at

any time, without notice or obligation.

• If you have any questions, or you find mistakes or omissions in the user’s manuals, please

contact our sales representative or your local distributor.

9th Edition: Aug. 05, 2015-00

Содержание EXA DO402G
































































































Результаты поиска

Содержание EXA DO402G

Отзывы:

Похожие инструкции для EXA DO402G

Бренды по названию

Популярные бренды

YOKOGAWA EXA DO402G, Руководство пользователя

Результаты поиска

Содержание EXA DO402G

Отзывы:

Похожие инструкции для EXA DO402G

Бренды по названию

Популярные бренды