YOKOGAWA DLM5034 Скачать руководство пользователя страница 43

Страница: 43 / 156

2-8

IM DLM5058-03EN

2.3 Connecting the Power Supply and Turning the Power Switch On and Off

Connecting the Power Cord

Check that the main power switch on the right side panel of the instrument is turned off.

Connect the power cord plug to the power connector on the right side panel.

Connect the other end of the cord to an outlet that meets the following conditions. Use a

grounded three-prong outlet.

Item

Rated supply voltage*

100 VAC to 120 VAC, 220 VAC to 240 VAC

Permitted supply voltage range

90 VAC to 132 VAC, 198 VAC to 264 VAC

Rated supply frequency

50/60 Hz

Permitted supply frequency range

48 Hz to 63 Hz

Maximum power consumption

290 VA

* This instrument can use a 100 V or a 200 V power supply. The maximum rated voltage differs

according to the type of power cord. Check that the voltage supplied to the instrument is less than or

equal to the maximum rated voltage of the power cord that you will be using before use.

Turning On the Power Switch

Before Turning On the Power, Check That:

• The instrument is installed properly. See section 2.2, “Appropriate Locations for Using the

Instrument.”

• The power cord is connected properly. See “Connecting the Power Cord,” described earlier.

Turning On the Main Power Switch

Switch the power switch on the right side panel to the ON ( | ) position.

The front-panel power switch illuminates in orange.

Содержание DLM5034





























































































































































Результаты поиска

Содержание DLM5034

Отзывы:

Похожие инструкции для DLM5034

Бренды по названию

Популярные бренды

YOKOGAWA DLM5034, Руководство пользователя

Результаты поиска

Содержание DLM5034

Отзывы:

Похожие инструкции для DLM5034

Бренды по названию

Популярные бренды