manualshive.com logo in svg

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 98 / 190

Поделиться
Скачать
YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 98

4-14

IM DL850-03EN

4.7  Calibrating the DL850/DL850V

CAL Menu

Press 

SHIFT+SETUP

 (CAL) to display the following menu.

 

Executes calibration

Turns auto calibration on and off

Calibration

The following items are calibrated. Execute calibration when you want to make accurate 
measurements.
•  Vertical axis ground level and gain
•  Trigger threshold level
•  Measured time value for repetitive sampling

Note

Calibration is performed automatically when the power switch is turned on.

Notes about Calibration

•  Allow the DL850/DL850V to warm up for at least 30 minutes before you execute calibration. If you 

execute calibration immediately after power-on, the calibrated values may drift due to temperature 
changes or other environmental changes.

•  Execute calibration in an environment with a stable temperature ranging from 5 to 40°C (23 ± 5°C 

recommended).

•  Do not apply signals when calibrating. Calibration may not be executed properly when input signals 

are being applied to the DL850/DL850V.

Auto Calibration (Auto Cal)

Auto calibration is executed when you start signal acquisition if you have changed Time/div and any of 
the time periods listed below has elapsed since the power was turned on.
•  3 minutes
•  10 minutes
•  30 minutes
•  One hour and every hour thereafter
If calibration is executed while signals are being applied to the DL850/DL850V, we recommend that 
you recalibrate the DL850/DL850V without any signals being applied to it.

Содержание DL850 ScopeCorder































































































































































































Отзывы:

Нет отзывов